SECS/GEM .NET API

The public .NET API of SECS/GEM.

All kindsClassConstructorDelegateEnumEnumeratorMethodPropertyStruct2084 symbols

• Gem300Axis.Carrier Enumerator — Carriers (SEMI E87).
• Gem300Axis.ControlJob Enumerator — Control jobs (SEMI E94).
• Gem300Axis.ProcessJob Enumerator — Process jobs (SEMI E40).
• Gem300Axis.Substrate Enumerator — Substrates (SEMI E90).
• Gem300Status.Experimental Enumerator — Label value 3 (experimental): the application runs the capability on trial.
• Gem300Status.ModelOnly Enumerator — Label value 2 (model only): the application has a data model of the capability.
• Gem300Status.Planned Enumerator — Label value 1 (planned): the application plans the capability.
• Gem300Verification.Unverified Enumerator — Verification label value 1, currently the only defined value.
• GemCommandDecision.AcceptedForLater Enumerator — HCACK 4: the command is accepted and will be performed, with completion signaled later by an event.
• GemCommandDecision.AlreadyInCondition Enumerator — HCACK 5: the command is rejected because the equipment is already in the requested condition.
• GemCommandDecision.CannotPerformNow Enumerator — HCACK 2: the command cannot be performed now.
• GemCommandDecision.Completed Enumerator — HCACK 0: the command has been performed.
• GemCommandDecision.NoSuchObject Enumerator — HCACK 6: the addressed object does not exist.
• GemCommandDecision.ParameterErrors Enumerator — HCACK 3: at least one parameter is invalid. This is the only decision that can carry parameter acknowledgements.
• GemCommandDecision.UnknownCommand Enumerator — HCACK 1: the command does not exist.
• GemCommunicationState.Communicating Enumerator — Communication is established, so other GEM transactions are allowed.
• GemCommunicationState.Disconnected Enumerator — The HSMS session is not selected, so no GEM communication is possible.
• GemCommunicationState.NotCommunicating Enumerator — The HSMS session is selected, but communication has not been established with S1F13/S1F14.
• GemCommunicationState.WaitingAck Enumerator — This endpoint sent S1F13 and is waiting for the S1F14 acknowledgement (COMMACK).
• GemConstantDecision.Apply Enumerator — Accept and apply the new values (EAC 0).
• GemConstantDecision.CannotPerform Enumerator — Deny because the equipment cannot perform the change now (EAC 2).
• GemConstantDecision.OutOfRange Enumerator — Deny because at least one value is out of range (EAC 3).
• GemConstantField.Current Enumerator — The current value (ECV). Valid only for GemEquipment.GetConstant.
• GemConstantField.Default Enumerator — The default value (ECDEF).
• GemConstantField.Id Enumerator — The equipment constant ID (ECID).
• GemConstantField.Maximum Enumerator — The upper bound (ECMAX).
• GemConstantField.Minimum Enumerator — The lower bound (ECMIN).
• GemConstantField.Name Enumerator — The constant name (ECNAME), as an ASCII item.
• GemConstantField.Units Enumerator — The units (UNITS), as an ASCII item.
• GemControlState.AttemptOnline Enumerator — The equipment sent S1F1 after GemEquipment.OperatorOnline and waits for the host reply. This state is not allowed as GemEquipmentOptions.InitialControl.
• GemControlState.EquipmentOffline Enumerator — The equipment is off-line by operator choice and does not accept S1F17 (Request On-line).
• GemControlState.HostOffline Enumerator — The equipment is off-line because the host requested it (S1F15) or the attempt to go on-line ended.
• GemControlState.OnlineLocal Enumerator — The equipment is on-line in local mode.
• GemControlState.OnlineRemote Enumerator — The equipment is on-line in remote mode.
• GemDataField.Cached Enumerator — A copy of the cached value, or no item when no value is cached.
• GemDataField.Name Enumerator — The name, as an ASCII item.
• GemDataField.Units Enumerator — The units, as an ASCII item.
• GemDataSourceKind.Constant Enumerator — The current value of an equipment constant; the constant ID (ECID) is given as an item and the source ID is 0.
• GemDataSourceKind.Data Enumerator — A data variable; the source ID is the data variable ID. The value comes from an event sample, else from the cached value.
• GemDataSourceKind.Status Enumerator — A status variable registered with GemEquipment.RegisterStatus; the source ID is the SVID.
• GemDirectoryField.Name Enumerator — The name as an ASCII item: DVVALNAME of a data variable entry or CENAME of an event entry.
• GemDirectoryField.Units Enumerator — The units (UNITS) of a data variable entry as an ASCII item. Not valid for event entries.
• GemDirectoryField.VariableIds Enumerator — The variable IDs (VIDs) of an event entry as a U4 array item. Not valid for data variable entries.
• GemDirectoryKind.Data Enumerator — The data variable namelist, requested with S1F21 and answered with S1F22. The value matches GemRequestKind.DataDirectory.
• GemDirectoryKind.Event Enumerator — The collection event namelist, requested with S1F23 and answered with S1F24. The value matches GemRequestKind.EventDirectory.
• GemError.Aborted Enumerator — The peer answered the request with an abort (function 0) reply.
• GemError.Ack Enumerator — The acknowledgement code in the reply is outside the range allowed for the transaction.
• GemError.Body Enumerator — The message body does not have the structure required by the transaction.
• GemError.Codec Enumerator — The SECS-II body cannot be decoded or exceeds the configured item limits.
• GemError.Correlation Enumerator — The reply does not correlate with the request, for example a different number of entries than IDs.
• GemError.Disconnected Enumerator — The endpoint has no selected HSMS session.
• GemError.MissingBody Enumerator — The message has no body although the transaction requires one.
• GemError.Response Enumerator — The message is not a valid answer for the pending request, or GEM rejected it for another protocol reason.
• GemError.State Enumerator — The message is not allowed in the current GEM communication or control state.
• GemError.UnexpectedBody Enumerator — The message has a body although the transaction requires a header-only message.
• GemError.Unsupported Enumerator — The stream and function are not supported by this endpoint role or configuration, or a reply has a different stream or function than the request expects.
• GemError.Wait Enumerator — The reply-expected (W) bit of the message does not match the transaction.
• GemFormattedProgramActionResult.Accepted Enumerator — The start was accepted and the execution is running. Valid only for a start action.
• GemFormattedProgramActionResult.Applied Enumerator — The step's command was applied and the next command becomes current. Valid only for a step action.
• GemFormattedProgramActionResult.Cancelled Enumerator — The cancel took effect and the execution ends. Valid only for a cancel action.
• GemFormattedProgramActionResult.Failed Enumerator — The action failed and the execution ends.
• GemFormattedProgramActionResult.OutcomeUnknown Enumerator — The application does not know whether the action took effect; the execution ends.
• GemFormattedProgramActionResult.Rejected Enumerator — The action was rejected. A rejected start or step ends the execution; a rejected cancel returns it to GemFormattedProgramExecutionState.Running.
• GemFormattedProgramDependency.Before Enumerator — The before-dependency list (BCDS).
• GemFormattedProgramDependency.ImmediateAfter Enumerator — The immediately-after dependency list (IACDS).
• GemFormattedProgramDependency.ImmediateBefore Enumerator — The immediately-before dependency list (IBCDS).
• GemFormattedProgramDependency.NonAfter Enumerator — The not-after dependency list (NACDS).
• GemFormattedProgramDependency.NonBefore Enumerator — The not-before dependency list (NBCDS).
• GemFormattedProgramDryRunOutcome.Indeterminate Enumerator — The analysis could not confirm every aspect, for example because no capability catalog is installed, but no issue rejects the program.
• GemFormattedProgramDryRunOutcome.Pass Enumerator — The analysis found no issue.
• GemFormattedProgramDryRunOutcome.Reject Enumerator — At least one issue rejects the program; GemFormattedPrograms.StartExecution refuses such a report.
• GemFormattedProgramExecutionState.ApplicationRejected Enumerator — The application rejected the start or a step.
• GemFormattedProgramExecutionState.CancelPending Enumerator — A cancel action waits for the application's result.
• GemFormattedProgramExecutionState.Cancelled Enumerator — The application confirmed a cancel action.
• GemFormattedProgramExecutionState.Completed Enumerator — The application reported that the program completed.
• GemFormattedProgramExecutionState.Empty Enumerator — No execution has been started.
• GemFormattedProgramExecutionState.Failed Enumerator — The application reported a failed action or a failed program.
• GemFormattedProgramExecutionState.OutcomeUnknown Enumerator — The application reported that it does not know the outcome of an action or of the program.
• GemFormattedProgramExecutionState.Running Enumerator — The application accepted the start; steps and a cancel can be requested.
• GemFormattedProgramExecutionState.StartPending Enumerator — A start action waits for the application's result.
• GemFormattedProgramExecutionState.StepPending Enumerator — A step action waits for the application's result.
• GemFormattedProgramStoreAction.CreateOnly Enumerator — Adds the program; fails with PdcommStatus.InvalidState when a program with the same PPID exists.
• GemFormattedProgramStoreAction.ReplaceOnly Enumerator — Replaces the stored program with the same PPID; fails with PdcommStatus.InvalidState when there is none.
• GemFormattedProgramStoreAction.RespondOnly Enumerator — Replies without changing the store. Only GemFormattedPrograms.RespondTransferAndStore accepts it.
• GemFormattedProgramStoreAction.Upsert Enumerator — Adds the program, or replaces the stored program with the same PPID.
• GemFormattedProgramTerminalOutcome.Complete Enumerator — The program completed; accepted only after every command was applied.
• GemFormattedProgramTerminalOutcome.Fail Enumerator — The program failed.
• GemFormattedProgramTerminalOutcome.OutcomeUnknown Enumerator — The application does not know the outcome of the program.
• GemOnlineMode.Local Enumerator — Going on-line enters GemControlState.OnlineLocal.
• GemOnlineMode.Remote Enumerator — Going on-line enters GemControlState.OnlineRemote.
• GemOutcome.AlarmAck Enumerator — The equipment received S5F2 for its alarm report; the acknowledgement holds ACKC5.
• GemOutcome.AlarmEnableAck Enumerator — An S5F3/S5F4 Enable/Disable Alarm transaction completed; the acknowledgement holds ACKC5.
• GemOutcome.AlarmListReceived Enumerator — The host received the S5F6 alarm list.
• GemOutcome.AlarmListReplied Enumerator — The equipment answered S5F5 with S5F6 automatically.
• GemOutcome.AlarmReceived Enumerator — The host received an S5F1 alarm report; acknowledge it explicitly when a reply is expected.
• GemOutcome.AlreadyOnline Enumerator — The equipment answered S1F17 with ONLACK 2 because it is already on-line.
• GemOutcome.AnnotatedQueryReceived Enumerator — The host received the S6F22 annotated individual report data.
• GemOutcome.CommandAck Enumerator — The host received S2F42; the acknowledgement holds HCACK.
• GemOutcome.CommandReceived Enumerator — The equipment received an S2F41 host command that waits for an explicit response.
• GemOutcome.CommunicationEstablished Enumerator — Communication is established: an S1F14 with COMMACK 0 was received, or a received S1F13 was accepted.
• GemOutcome.CommunicationRejected Enumerator — The peer rejected S1F13; GemResultInfo.Acknowledgement holds the nonzero COMMACK.
• GemOutcome.ConstantChangeAck Enumerator — The host received S2F16; the acknowledgement holds EAC.
• GemOutcome.ConstantChangesReceived Enumerator — The equipment received S2F15 constant changes that wait for an explicit decision.
• GemOutcome.ConstantMetadataReceived Enumerator — The host received the S2F30 equipment constant name list.
• GemOutcome.ConstantMetadataReplied Enumerator — The equipment answered S2F29 with S2F30 automatically.
• GemOutcome.ConstantValuesReceived Enumerator — The host received the S2F14 equipment constant values.
• GemOutcome.ConstantValuesReplied Enumerator — The equipment answered S2F13 with S2F14 automatically.
• GemOutcome.DataDirectoryReceived Enumerator — The host received the S1F22 data variable name list.
• GemOutcome.DataDirectoryReplied Enumerator — The equipment answered S1F21 with S1F22 automatically.
• GemOutcome.DefineReportsAck Enumerator — An S2F33/S2F34 Define Report transaction completed; the acknowledgement holds DRACK.
• GemOutcome.EnableEventsAck Enumerator — An S2F37/S2F38 Enable/Disable Event Report transaction completed; the acknowledgement holds ERACK.
• GemOutcome.EnabledAlarmListReceived Enumerator — The host received the S5F8 enabled alarm list.
• GemOutcome.EnabledAlarmListReplied Enumerator — The equipment answered S5F7 with S5F8 automatically.
• GemOutcome.EnhancedCommandAck Enumerator — The host received S2F50; the acknowledgement holds HCACK.
• GemOutcome.EnhancedCommandReceived Enumerator — The equipment received an S2F49 enhanced remote command that waits for an explicit response.
• GemOutcome.EquipmentIdentity Enumerator — The host received the S1F2 reply with the equipment model (MDLN) and software revision (SOFTREV).
• GemOutcome.EventAck Enumerator — The equipment received S6F12 for its event report; the acknowledgement holds ACKC6.
• GemOutcome.EventDirectoryReceived Enumerator — The host received the S1F24 collection event name list.
• GemOutcome.EventDirectoryReplied Enumerator — The equipment answered S1F23 with S1F24 automatically.
• GemOutcome.EventQueryReceived Enumerator — The host received the S6F16 event report data.
• GemOutcome.EventReceived Enumerator — The host received an S6F11 event report; acknowledge it explicitly.
• GemOutcome.FormattedCapabilityReceived Enumerator — The equipment received an S7F21 process capabilities request.
• GemOutcome.FormattedCapabilityResult Enumerator — The host received the S7F22 process capabilities data.
• GemOutcome.FormattedQueryReceived Enumerator — The equipment received an S7F25 formatted process program request.
• GemOutcome.FormattedQueryResult Enumerator — The host received the S7F26 formatted process program data.
• GemOutcome.FormattedTransferAck Enumerator — The host received the S7F24 formatted process program acknowledgement.
• GemOutcome.FormattedTransferReceived Enumerator — The equipment received an S7F23 formatted process program.
• GemOutcome.FormattedVerificationGrantReceived Enumerator — The equipment received the S7F30 verification grant (PPGNT).
• GemOutcome.FormattedVerificationInquireReceived Enumerator — The host received an S7F29 process program verification inquire.
• GemOutcome.FormattedVerificationNegotiationAck Enumerator — The equipment received the S7F28 acknowledgement that completes a verification negotiation.
• GemOutcome.FormattedVerificationReportAck Enumerator — The equipment received the S7F28 verification acknowledgement.
• GemOutcome.FormattedVerificationReportReceived Enumerator — The host received an S7F27 process program verification send.
• GemOutcome.FormattedVerificationRequestAck Enumerator — The host received the S7F32 verification request acknowledgement.
• GemOutcome.FormattedVerificationRequestReceived Enumerator — The equipment received an S7F31 verification request.
• GemOutcome.IndividualQueryReceived Enumerator — The host received the S6F20 individual report data.
• GemOutcome.LinkReportsAck Enumerator — An S2F35/S2F36 Link Event Report transaction completed; the acknowledgement holds LRACK.
• GemOutcome.NamesReceived Enumerator — The host received a validated S1F12 status name list; read it with GemResult.GetStatusName.
• GemOutcome.None Enumerator — No outcome; the result is ignored, failed, invalid or unhandled.
• GemOutcome.OfflineAccepted Enumerator — The equipment accepted S1F15 and replied with OFLACK 0.
• GemOutcome.OfflineAck Enumerator — The host received S1F16; GemResultInfo.Acknowledgement holds OFLACK.
• GemOutcome.OnlineAccepted Enumerator — The equipment went on-line: it accepted S1F17 (ONLACK 0) or received the S1F2 reply to its operator on-line request.
• GemOutcome.OnlineAck Enumerator — The host received S1F18; GemResultInfo.Acknowledgement holds ONLACK.
• GemOutcome.OnlineRejected Enumerator — The equipment answered S1F17 with ONLACK 1 because it does not allow going on-line.
• GemOutcome.ProgramAckReceived Enumerator — The S7F4 or S7F18 process program acknowledgement was received; the acknowledgement holds ACKC7.
• GemOutcome.ProgramDataReceived Enumerator — The S7F6 process program data was received.
• GemOutcome.ProgramDirectoryReceived Enumerator — The S7F20 process program directory was received.
• GemOutcome.ProgramGrantReceived Enumerator — The S7F2 process program grant was received; the acknowledgement holds PPGNT.
• GemOutcome.ProgramReceived Enumerator — A stream 7 process program primary was received; GemResultInfo.RequestKind names the transaction.
• GemOutcome.Replied Enumerator — GEM answered a received primary automatically with a reply that has no more specific outcome.
• GemOutcome.ReportQueryReceived Enumerator — The equipment received an S6F15, S6F19 or S6F21 report query that waits for GemEquipment.RespondReportQuery.
• GemOutcome.SpoolConfigurationAck Enumerator — The host received the S2F44 spooling configuration acknowledgement.
• GemOutcome.SpoolConfigurationData Enumerator — The host received the S2F60 spooling configuration data.
• GemOutcome.SpoolControlAck Enumerator — The host received the S6F24 spooled data request acknowledgement.
• GemOutcome.SpoolDeliveryFailed Enumerator — The delivery of a spooled message failed.
• GemOutcome.SpoolDeliveryResponse Enumerator — The equipment received the reply to a delivered spooled message.
• GemOutcome.SpoolDeliveryWritten Enumerator — A delivered spooled message that expects no reply was written to the transport.
• GemOutcome.SpoolReceived Enumerator — The equipment received an S2F43, S2F59 or S6F23 spooling primary.
• GemOutcome.StatusReplied Enumerator — The equipment answered S1F3 or S1F11 automatically from its status variable registry.
• GemOutcome.ValuesReceived Enumerator — The host received validated S1F4 status values; read them with GemResult.GetStatusValue.
• GemProgramDurability.Confirmed Enumerator — The application accepted an unconfirmed installation with GemEquipment.ConfirmProgramReply. This does not mean that the change was synchronized, and is distinct from GemProgramDurability.Synced.
• GemProgramDurability.None Enumerator — No local change is associated, for example for a rejected request, a request that does not write, or a reply received from the peer.
• GemProgramDurability.Synced Enumerator — The change was written to the storage file and the file's parent directory was synchronized.
• GemProgramDurability.Unconfirmed Enumerator — The change was installed, but its persistence could not be confirmed; the persistence status holds the failure. Do not repeat the change as if it had been rolled back.
• GemProgramDurability.Volatile Enumerator — The change was installed in memory only, because the store has no storage file.
• GemProgramField.Body Enumerator — The process program body (PPBODY).
• GemProgramField.Id Enumerator — A process program ID (PPID).
• GemProgramGrantPolicy.Optional Enumerator — Accept S7F3 without a grant while no other grant is outstanding; with an outstanding grant for another PPID the reply is ACKC7 5.
• GemProgramGrantPolicy.Required Enumerator — Accept S7F3 only for a PPID granted by an accepted S7F1 on the same connection; otherwise the reply is ACKC7 1 (permission not granted).
• GemProgramPutMode.Create Enumerator — Store only a new PPID; an existing PPID is rejected.
• GemProgramPutMode.Replace Enumerator — Replace only an existing PPID; an unknown PPID is rejected.
• GemProgramPutMode.Upsert Enumerator — Create the PPID or replace it when it exists.
• GemReportQueryKind.Annotated Enumerator — Annotated individual report request by report ID (RPTID), S6F21/S6F22.
• GemReportQueryKind.Event Enumerator — Event report request by collection event ID (CEID), S6F15/S6F16.
• GemReportQueryKind.Individual Enumerator — Individual report request by report ID (RPTID), S6F19/S6F20.
• GemRequestKind.AlarmList Enumerator — List alarms request, S5F5/S5F6.
• GemRequestKind.AlarmReport Enumerator — Alarm Report Send, S5F1/S5F2.
• GemRequestKind.AnnotatedQuery Enumerator — Annotated individual report request by RPTID, S6F21/S6F22.
• GemRequestKind.AreYouOnline Enumerator — Are You There, S1F1/S1F2, sent by the host with GemHost.AreYouOnline. The equipment's operator-initiated S1F1 is reported as GemRequestKind.OperatorOnline.
• GemRequestKind.ChangeConstants Enumerator — New equipment constant send, S2F15/S2F16.
• GemRequestKind.ConstantMetadata Enumerator — Equipment constant name list request, S2F29/S2F30.
• GemRequestKind.ConstantValues Enumerator — Equipment constant values request, S2F13/S2F14.
• GemRequestKind.DataDirectory Enumerator — Data variable name list request, S1F21/S1F22.
• GemRequestKind.DefineReports Enumerator — Define Report, S2F33/S2F34.
• GemRequestKind.EnableAlarm Enumerator — Enable/Disable Alarm Send, S5F3/S5F4.
• GemRequestKind.EnableEvents Enumerator — Enable/Disable Event Report, S2F37/S2F38.
• GemRequestKind.EnabledAlarmList Enumerator — List enabled alarms request, S5F7/S5F8.
• GemRequestKind.EnhancedRemoteCommand Enumerator — Enhanced remote command, S2F49/S2F50.
• GemRequestKind.Establish Enumerator — Establish Communications, S1F13/S1F14.
• GemRequestKind.EventDirectory Enumerator — Collection event name list request, S1F23/S1F24.
• GemRequestKind.EventQuery Enumerator — Event report request by CEID, S6F15/S6F16.
• GemRequestKind.EventReport Enumerator — Event Report Send, S6F11/S6F12.
• GemRequestKind.FormattedCapability Enumerator — Equipment process capabilities request, S7F21/S7F22.
• GemRequestKind.FormattedQuery Enumerator — Formatted process program request, S7F25/S7F26.
• GemRequestKind.FormattedTransfer Enumerator — Formatted process program send, S7F23/S7F24.
• GemRequestKind.FormattedVerificationNegotiation Enumerator — Process program verification inquire and grant, S7F29/S7F30, followed by the S7F27/S7F28 verification send.
• GemRequestKind.FormattedVerificationReport Enumerator — Process program verification send, S7F27/S7F28.
• GemRequestKind.FormattedVerificationRequest Enumerator — Verification request send, S7F31/S7F32.
• GemRequestKind.IndividualQuery Enumerator — Individual report request by RPTID, S6F19/S6F20.
• GemRequestKind.LinkReports Enumerator — Link Event Report, S2F35/S2F36.
• GemRequestKind.Offline Enumerator — Request Off-line, S1F15/S1F16.
• GemRequestKind.Online Enumerator — Request On-line, S1F17/S1F18.
• GemRequestKind.OperatorOnline Enumerator — The equipment's operator-initiated ON-LINE attempt, S1F1/S1F2, sent with GemEquipment.OperatorOnline. Results of that transaction report this kind.
• GemRequestKind.ProgramDelete Enumerator — Delete process program send, S7F17/S7F18.
• GemRequestKind.ProgramDirectory Enumerator — Current process program directory request, S7F19/S7F20.
• GemRequestKind.ProgramGrant Enumerator — Process program load inquire and grant, S7F1/S7F2.
• GemRequestKind.ProgramRequest Enumerator — Process program request, S7F5/S7F6.
• GemRequestKind.ProgramSend Enumerator — Process program send, S7F3/S7F4.
• GemRequestKind.RemoteCommand Enumerator — Host command (RCMD) send, S2F41/S2F42.
• GemRequestKind.SpoolConfigure Enumerator — Reset spooled streams and functions, S2F43/S2F44.
• GemRequestKind.SpoolControl Enumerator — Request spooled data (transmit or purge), S6F23/S6F24.
• GemRequestKind.SpoolDelivery Enumerator — Delivery of one spooled primary message by the equipment. The message keeps the stream and function it was spooled with.
• GemRequestKind.SpoolQuery Enumerator — Spooling configuration query, S2F59/S2F60.
• GemRequestKind.StatusNames Enumerator — Status variable name list request, S1F11/S1F12.
• GemRequestKind.StatusValues Enumerator — Selected status variable values request, S1F3/S1F4.
• GemResultKind.Failed Enumerator — A GEM request ended without a usable reply. GemResultInfo.Code holds an HsmsFailureReason value, or GemError.Aborted when the peer answered with an abort (function 0) reply.
• GemResultKind.Ignored Enumerator — The event is not GEM traffic for this endpoint, for example a state change or a reply to a raw request.
• GemResultKind.InvalidResponse Enumerator — A reply arrived for a GEM request but failed validation. GemResultInfo.Code holds a GemError value; only the matched pending request is cleared.
• GemResultKind.Primary Enumerator — A received primary message was accepted by GEM. Some primaries are answered automatically (GemResultInfo.ReplySent); others wait for an explicit response from the application.
• GemResultKind.Response Enumerator — A validated reply to a GEM request this endpoint sent.
• GemResultKind.Unhandled Enumerator — A received primary message was not handled and no reply was sent. GemResultInfo.Code holds a GemError value. When the primary expects a reply, answer it with GemEndpoint.ReplyRaw (for example an F0 abort) or close the endpoint; no automatic S9 or F0 reply is sent.
• GemRole.Equipment Enumerator — The endpoint is GEM equipment (GemEquipment).
• GemRole.Host Enumerator — The endpoint is a GEM host (GemHost).
• GemSpoolCommand.Purge Enumerator — RSDC 1: purge the spooled messages.
• GemSpoolCommand.Transmit Enumerator — RSDC 0: transmit the spooled messages to the host.
• GemSpoolDeliveryProof.None Enumerator — The result carries no delivery evidence.
• GemSpoolDeliveryProof.Response Enumerator — The host's reply to an entry sent with the W-bit was received.
• GemSpoolDeliveryProof.Written Enumerator — The whole frame of an entry sent without the W-bit was written to the transport; this proves local write completion only, not receipt by the host.
• GemSpoolDurability.Confirmed Enumerator — The application accepted an unconfirmed change with GemEquipment.ConfirmSpoolReply; reported only by GemSpoolInfo.Durability.
• GemSpoolDurability.None Enumerator — No change was installed.
• GemSpoolDurability.Synced Enumerator — The change was written to the snapshot file, renamed into place and the parent directory was synchronized.
• GemSpoolDurability.Unconfirmed Enumerator — The change was installed and its snapshot file renamed into place, but synchronizing the parent directory failed, so the change may not survive a power loss.
• GemSpoolDurability.Volatile Enumerator — The change was installed in an in-memory spool and is lost when the endpoint is disposed.
• GemSpoolMutation.Activated Enumerator — Spooling became active because it is enabled and communication is down.
• GemSpoolMutation.Captured Enumerator — A message was stored; GemSpoolWriteResult.AffectedCount is the number of older entries that GemSpoolOverflow.OverwriteOldest removed to make room.
• GemSpoolMutation.Configured Enumerator — The policy or the stream selection was replaced, or a new spool was created with its initial disabled configuration.
• GemSpoolMutation.Discarded Enumerator — A selected message was discarded because it did not fit, and only the counters changed.
• GemSpoolMutation.None Enumerator — Nothing was changed.
• GemSpoolMutation.Purged Enumerator — Every entry was removed; GemSpoolWriteResult.AffectedCount is the number of removed entries.
• GemSpoolMutation.Removed Enumerator — The delivered head entry was removed from the spool.
• GemSpoolOverflow.DiscardNew Enumerator — Keeps the stored entries and discards the new message.
• GemSpoolOverflow.OverwriteOldest Enumerator — Removes the oldest entries until the new message fits, but never the entry whose delivery is in progress.
• HsmsConnectionState.Connecting Enumerator — An active endpoint is opening a TCP connection.
• HsmsConnectionState.Listening Enumerator — A passive endpoint is waiting for a TCP connection.
• HsmsConnectionState.NotSelected Enumerator — A TCP connection exists but the HSMS session is not selected yet.
• HsmsConnectionState.RetryWait Enumerator — An active endpoint is waiting for the T5 connect separation time before it reconnects.
• HsmsConnectionState.Selected Enumerator — The HSMS session is selected; data messages can be exchanged.
• HsmsConnectionState.Stopped Enumerator — The endpoint is not started, or it has stopped.
• HsmsEventKind.Failed Enumerator — A request or control transaction of this endpoint failed; HsmsEventInfo.Code holds the HsmsFailureReason.
• HsmsEventKind.ProtocolError Enumerator — The peer violated the HSMS protocol; HsmsEventInfo.Code holds the HsmsProtocolError.
• HsmsEventKind.Received Enumerator — A data message arrived: a primary message or the reply to one of this endpoint's requests.
• HsmsEventKind.StateChanged Enumerator — The connection state changed; see HsmsEventInfo.FromState and HsmsEventInfo.ToState.
• HsmsEventKind.TransportError Enumerator — A socket operation failed; HsmsEventInfo.Code holds the HsmsIoOperation and HsmsEventInfo.Detail the HsmsIoErrorKind.
• HsmsEventKind.W0Written Enumerator — A message sent without the reply-expected (W) bit was completely written to the socket.
• HsmsFailureReason.Cancelled Enumerator — The transaction was cancelled locally.
• HsmsFailureReason.DeselectStatus Enumerator — The peer refused Deselect.req; HsmsEventInfo.Value1 holds the DeselectStatus.
• HsmsFailureReason.Deselected Enumerator — The session was deselected before the transaction completed.
• HsmsFailureReason.Disconnected Enumerator — The connection closed before the transaction completed.
• HsmsFailureReason.Rejected Enumerator — The peer answered with Reject.req; HsmsEventInfo.Value1 holds the rejected message type and HsmsEventInfo.Value2 the reason code.
• HsmsFailureReason.SelectStatus Enumerator — The peer refused Select.req; HsmsEventInfo.Value1 holds the SelectStatus.
• HsmsFailureReason.T3Timeout Enumerator — No reply arrived within the T3 reply timeout.
• HsmsFailureReason.T6Timeout Enumerator — No control response arrived within the T6 control transaction timeout.
• HsmsFrameError.BufferTooSmall Enumerator — An output buffer was too small for the frame.
• HsmsFrameError.ControlBody Enumerator — A control message carried a body.
• HsmsFrameError.ControlSession Enumerator — A control message other than Reject.req did not carry session ID 0xFFFF.
• HsmsFrameError.HeaderField Enumerator — A header byte has a value that the message type does not allow.
• HsmsFrameError.InvalidLength Enumerator — The length field declares fewer bytes than the 10-byte HSMS header.
• HsmsFrameError.LengthOverflow Enumerator — The declared length overflows the platform's size range.
• HsmsFrameError.LimitExceeded Enumerator — The frame exceeds the configured frame limit.
• HsmsFrameError.NeedMore Enumerator — More bytes are needed to complete the frame.
• HsmsFrameError.NotData Enumerator — A data message was expected but a control message arrived.
• HsmsFrameError.ReaderFailed Enumerator — The frame reader already failed on this connection and accepts no more input.
• HsmsFrameError.SecsBody Enumerator — The body of a data message is not one valid SECS-II item.
• HsmsFrameError.TrailingData Enumerator — Bytes follow the frame where none were expected.
• HsmsFrameError.UnsupportedPType Enumerator — The header's PType is not 0 (SECS-II).
• HsmsFrameError.UnsupportedSType Enumerator — The header's SType is not a supported HSMS message type.
• HsmsIoErrorKind.Aborted Enumerator — The connection was aborted.
• HsmsIoErrorKind.AddressInUse Enumerator — The local address is already in use.
• HsmsIoErrorKind.AddressUnavailable Enumerator — The requested address is not available.
• HsmsIoErrorKind.BrokenPipe Enumerator — The connection was closed while writing.
• HsmsIoErrorKind.Interrupted Enumerator — The operation was interrupted.
• HsmsIoErrorKind.InvalidData Enumerator — Invalid data was encountered.
• HsmsIoErrorKind.InvalidInput Enumerator — An input parameter was invalid.
• HsmsIoErrorKind.NotConnected Enumerator — The socket is not connected.
• HsmsIoErrorKind.NotFound Enumerator — An entity was not found.
• HsmsIoErrorKind.Other Enumerator — Any error not listed below.
• HsmsIoErrorKind.Permission Enumerator — The operation lacked permission.
• HsmsIoErrorKind.Refused Enumerator — The peer refused the connection.
• HsmsIoErrorKind.Reset Enumerator — The peer reset the connection.
• HsmsIoErrorKind.TimedOut Enumerator — The operation timed out.
• HsmsIoErrorKind.UnexpectedEof Enumerator — The connection ended in the middle of a frame.
• HsmsIoErrorKind.WouldBlock Enumerator — The operation would block.
• HsmsIoErrorKind.WriteZero Enumerator — A write returned zero bytes.
• HsmsIoOperation.Accept Enumerator — Accepting an incoming connection.
• HsmsIoOperation.Bind Enumerator — Binding the listening socket.
• HsmsIoOperation.Configure Enumerator — Configuring socket options.
• HsmsIoOperation.Connect Enumerator — Connecting to the peer.
• HsmsIoOperation.LocalAddress Enumerator — Reading the local socket address.
• HsmsIoOperation.Read Enumerator — Reading from the connection.
• HsmsIoOperation.Write Enumerator — Writing to the connection.
• HsmsMode.Active Enumerator — The endpoint opens the TCP connection and sends Select.req.
• HsmsMode.Passive Enumerator — The endpoint binds a listening socket when it is created and accepts one connection at a time.
• HsmsProtocolError.DuplicatePrimary Enumerator — A primary that expects a reply reused the system bytes of a received primary that is still open.
• HsmsProtocolError.FrameLimit Enumerator — Reserved for a frame above HsmsOptions.MaxFrameBytes. The current native library does not report it: such a frame closes the connection with a transport error (HsmsIoOperation.Read, HsmsIoErrorKind.InvalidData).
• HsmsProtocolError.IncomingLimit Enumerator — Too many received primaries are waiting for replies; the endpoint answered the new one with an abort (function 0).
• HsmsProtocolError.InvalidFrame Enumerator — A frame was malformed; HsmsEventInfo.Detail holds the HsmsFrameError.
• HsmsProtocolError.InvalidReject Enumerator — A Reject.req message was malformed.
• HsmsProtocolError.InvalidReply Enumerator — A reply message was malformed or did not fit its request.
• HsmsProtocolError.UnexpectedControl Enumerator — A control response matched no open control transaction.
• HsmsProtocolError.UnexpectedReply Enumerator — A reply matched no open request of this endpoint.
• HsmsProtocolError.WrongSession Enumerator — A data message carried another session ID; HsmsEventInfo.Value1 holds the expected and HsmsEventInfo.Value2 the received ID.
• Secs1Direction.ToEquipment Enumerator — The message travels from the host to the equipment (R-bit 0).
• Secs1Direction.ToHost Enumerator — The message travels from the equipment to the host (R-bit 1).
• Secs1EventKind.Fault Enumerator — The line faulted; see Secs1Event.FaultKind. The endpoint stops until Secs1Worker.ResetAsync clears the fault.
• Secs1EventKind.Inbound Enumerator — A complete message was received; see Secs1Event.Message.
• Secs1EventKind.OutboundComplete Enumerator — The peer acknowledged every block of a submitted message; see Secs1Event.Token.
• Secs1EventKind.OutboundFailed Enumerator — A submitted message failed after its retries were exhausted; see Secs1Event.Token.
• Secs1IoStatus.Aborted Enumerator — The connection was aborted.
• Secs1IoStatus.AddressInUse Enumerator — The address is already in use.
• Secs1IoStatus.AddressUnavailable Enumerator — The address is not available.
• Secs1IoStatus.BrokenPipe Enumerator — The peer closed the stream while writing.
• Secs1IoStatus.Closed Enumerator — The serial port or stream is closed.
• Secs1IoStatus.Interrupted Enumerator — The operation was interrupted; try again on a later poll.
• Secs1IoStatus.InvalidData Enumerator — Invalid data was encountered.
• Secs1IoStatus.InvalidInput Enumerator — An input parameter was invalid.
• Secs1IoStatus.NotConnected Enumerator — The stream is not connected.
• Secs1IoStatus.NotFound Enumerator — The device was not found.
• Secs1IoStatus.Ok Enumerator — The operation transferred Secs1IoResult.Count bytes.
• Secs1IoStatus.Other Enumerator — Any other failure; also reported when a callback throws.
• Secs1IoStatus.Permission Enumerator — Access was denied.
• Secs1IoStatus.Refused Enumerator — The connection was refused.
• Secs1IoStatus.Reset Enumerator — The connection was reset.
• Secs1IoStatus.TimedOut Enumerator — The operation timed out.
• Secs1IoStatus.WouldBlock Enumerator — No bytes are available now; try again on a later poll.
• Secs1IoStatus.WriteZero Enumerator — A write accepted zero bytes.
• Secs1Priority.Master Enumerator — On contention (both sides send ENQ), keep waiting for the peer's EOT.
• Secs1Priority.Slave Enumerator — On contention, yield: answer the peer's ENQ with EOT and receive first.
• SecsFormat.Ascii Enumerator — ASCII text (A, octal 20): 7-bit characters, one byte each.
• SecsFormat.Binary Enumerator — Binary (B, octal 10): uninterpreted bytes.
• SecsFormat.Boolean Enumerator — Boolean (BOOLEAN, octal 11): one byte per value, nonzero means true.
• SecsFormat.F4 Enumerator — 4-byte IEEE 754 floating-point values (F4, octal 44).
• SecsFormat.F8 Enumerator — 8-byte IEEE 754 floating-point values (F8, octal 40).
• SecsFormat.I1 Enumerator — 1-byte signed integers (I1, octal 31).
• SecsFormat.I2 Enumerator — 2-byte signed integers (I2, octal 32).
• SecsFormat.I4 Enumerator — 4-byte signed integers (I4, octal 34).
• SecsFormat.I8 Enumerator — 8-byte signed integers (I8, octal 30).
• SecsFormat.Jis8 Enumerator — JIS-8 text (J, octal 21): bytes kept as received.
• SecsFormat.List Enumerator — List (L, octal 00): an ordered sequence of child items.
• SecsFormat.U1 Enumerator — 1-byte unsigned integers (U1, octal 51).
• SecsFormat.U2 Enumerator — 2-byte unsigned integers (U2, octal 52).
• SecsFormat.U4 Enumerator — 4-byte unsigned integers (U4, octal 54).
• SecsFormat.U8 Enumerator — 8-byte unsigned integers (U8, octal 50).
• Gem300Capability.Gem300Capability Constructor — One capability of a GEM300 capability profile.
• Gem300CapabilityCatalog.Gem300CapabilityCatalog Constructor — Creates an empty catalog with the given limits.
• Gem300CapabilityCatalog.Clear Method — Removes every profile from the catalog.
• Gem300CapabilityCatalog.GetInfo Method — Gets the revision and size of the catalog.
• Gem300CapabilityCatalog.Replace Method — Replaces the whole catalog with the given profiles.
• Gem300CapabilityCatalog.Snapshot Method — Takes an immutable copy of the catalog.
• Gem300CapabilityCatalogInfo.Gem300CapabilityCatalogInfo Constructor — Describes the contents of a GEM300 capability catalog or of a snapshot of it.
• Gem300CapabilityInfo.Gem300CapabilityInfo Constructor — Describes one capability of a GEM300 capability profile.
• Gem300CapabilityOptions.Gem300CapabilityOptions Constructor — Limits that bound the contents of a Gem300CapabilityCatalog.
• Gem300CapabilityProfile.Gem300CapabilityProfile Constructor — A named set of GEM300 capabilities, at most one per axis.
• Gem300CapabilityProfileInfo.Gem300CapabilityProfileInfo Constructor — Describes one profile of a GEM300 capability snapshot.
• Gem300CapabilitySnapshot.GetInfo Method — Gets the revision and size of the catalog when the snapshot was taken.
• Gem300CapabilitySnapshot.GetProfile Method — Gets one profile of the snapshot with all of its capabilities.
• Gem300CatalogChange.Gem300CatalogChange Constructor — The outcome of a change to a Gem300CapabilityCatalog.
• GemAlarmChange.GemAlarmChange Constructor — Represents the result of GemEquipment.ObserveAlarm.
• GemAlarmConfiguration.GemAlarmConfiguration Constructor — Represents the alarm store that GemEquipmentWorker installs on its equipment endpoint at startup.
• GemAlarmDefinition.GemAlarmDefinition Constructor — Defines one equipment alarm for GemEquipment.ConfigureAlarms.
• GemAlarmEntry.GemAlarmEntry Constructor — Represents one configured equipment alarm together with its text.
• GemAlarmInfo.GemAlarmInfo Constructor — Represents the local state and metadata of one configured equipment alarm.
• GemAlarmOptions.GemAlarmOptions Constructor — Initializes a new instance with default values.
• GemAlarmResultInfo.GemAlarmResultInfo Constructor — Describes an alarm report or alarm list carried by a host-side GemResult.
• GemAlarmState.GemAlarmState Constructor — Represents a snapshot of the counters of the configured equipment alarm store.
• GemAlarmValue.GemAlarmValue Constructor — Represents one alarm entry received from the equipment together with its text.
• GemAlarmValueInfo.GemAlarmValueInfo Constructor — Represents the fields of one alarm entry received from the equipment.
• GemBindingOptions.GemBindingOptions Constructor — Initializes a new instance with default values.
• GemBindingState.GemBindingState Constructor — Represents the current state of an equipment's report variable bindings.
• GemCommandArgument.Dispose Method — Releases the native name and value items.
• GemCommandConfiguration.GemCommandConfiguration Constructor — Represents the remote command store that GemEquipmentWorker installs on its equipment endpoint at startup.
• GemCommandDefinition.GemCommandDefinition Constructor — Defines one remote command that the equipment validates on receipt.
• GemCommandEntry.Dispose Method — Releases the native name item.
• GemCommandError.Dispose Method — Releases the native name item.
• GemCommandInfo.GemCommandInfo Constructor — Represents the metadata of one configured remote command.
• GemCommandIssue.GemCommandIssue Constructor — Represents one parameter acknowledgement that the equipment returns in an S2F42 reply.
• GemCommandOptions.GemCommandOptions Constructor — Initializes a new instance with default values.
• GemCommandParameter.GemCommandParameter Constructor — Represents one parameter that the host sends with a remote command.
• GemCommandParameterDefinition.GemCommandParameterDefinition Constructor — Defines one parameter of a remote command definition.
• GemCommandParameterEntry.Dispose Method — Releases the native name item.
• GemCommandParameterInfo.GemCommandParameterInfo Constructor — Represents the validation rules of one configured remote command parameter.
• GemCommandReply.GemCommandReply Constructor — Represents the S2F42 reply that the equipment sent for a remote command.
• GemCommandResultInfo.GemCommandResultInfo Constructor — Describes a remote command request received by the equipment (S2F41) or a remote command reply received by the host (S2F42).
• GemCommandState.GemCommandState Constructor — Represents a snapshot of the counters of the configured remote command store.
• GemConstantChange.GemConstantChange Constructor — Represents one new value for an equipment constant in an S2F15 (New Equipment Constant Send) request.
• GemConstantChangeEntry.Dispose Method — Releases GemConstantChangeEntry.Id, GemConstantChangeEntry.Value and GemConstantChangeEntry.Original.
• GemConstantChangeInfo.GemConstantChangeInfo Constructor — Represents the processing state of an S2F15 request result or an S2F16 reply result.
• GemConstantConfiguration.GemConstantConfiguration Constructor — Represents the equipment constant store that GemEquipmentWorker installs on its equipment endpoint at startup.
• GemConstantDefinition.GemConstantDefinition Constructor — Represents one equipment constant to register with GemEquipment.ConfigureConstants.
• GemConstantEntry.Dispose Method — Releases GemConstantEntry.Id.
• GemConstantInfo.GemConstantInfo Constructor — Represents the declared shape of one registered equipment constant.
• GemConstantOptions.GemConstantOptions Constructor — Initializes a new instance with default values.
• GemConstantReply.GemConstantReply Constructor — Represents the S2F16 reply sent by GemEquipment.RespondConstants.
• GemConstantState.GemConstantState Constructor — Represents the counters of the equipment constant store.
• GemConstantValue.Dispose Method — Releases GemConstantValue.Id and GemConstantValue.Value.
• GemDataConfiguration.GemDataConfiguration Constructor — Represents the data variables and optional report bindings that a GemEquipmentWorker configures when it starts.
• GemDataDefinition.GemDataDefinition Constructor — Represents the definition of one data variable in an equipment's data variable store.
• GemDataInfo.GemDataInfo Constructor — Represents the shape and cache state of one data variable.
• GemDataOptions.GemDataOptions Constructor — Initializes a new instance with default values.
• GemDataSample.GemDataSample Constructor — Represents a data variable value supplied for one event report.
• GemDataState.GemDataState Constructor — Represents the current counters of an equipment's data variable store.
• GemDirectoryConfiguration.GemDirectoryConfiguration Constructor — Represents the collection event directory that a GemEquipmentWorker configures when it starts.
• GemDirectoryEntryInfo.GemDirectoryEntryInfo Constructor — Represents the ID and variable count of one directory entry.
• GemDirectoryOptions.GemDirectoryOptions Constructor — Initializes a new instance with default values.
• GemDirectoryState.GemDirectoryState Constructor — Represents the current counters of an equipment's event directory.
• GemEndpoint.BeginCommunication Method — Sends S1F13 (Establish Communications Request) to start GEM communication.
• GemEndpoint.Cancel Method — Cancels a pending transaction.
• GemEndpoint.Deselect Method — Sends an HSMS Deselect.req control message.
• GemEndpoint.Dispose Method — Releases the native endpoint without a graceful wire shutdown.
• GemEndpoint.GetLocalAddress Method — Gets the numeric local socket address, for example the bound address of a passive endpoint.
• GemEndpoint.GetState Method — Gets a snapshot of the GEM state.
• GemEndpoint.GetTransportState Method — Gets the HSMS connection state of the underlying transport.
• GemEndpoint.HandleEvent Method — Processes one transport event with the GEM layer.
• GemEndpoint.IsPending Method — Gets whether a transaction is still waiting for its reply.
• GemEndpoint.Linktest Method — Sends an HSMS Linktest.req control message.
• GemEndpoint.NextEvent Method — Removes the next transport event from the endpoint queue.
• GemEndpoint.Poll Method — Performs pending transport work such as connecting, reading, writing and timer checks.
• GemEndpoint.ReplyRaw Method — Sends a raw SECS-II reply to a received primary message.
• GemEndpoint.RequestRaw Method — Sends a raw SECS-II primary message that GEM does not track.
• GemEndpoint.Select Method — Sends an HSMS Select.req control message.
• GemEndpoint.Start Method — Starts the HSMS transport: an active endpoint starts connecting and a passive endpoint starts listening.
• GemEndpoint.Stop Method — Starts closing the HSMS transport; keep polling and draining events until the state reports closed.
• GemEnhancedCommandConfiguration.GemEnhancedCommandConfiguration Constructor — Represents the enhanced remote command store that GemEquipmentWorker installs on its equipment endpoint at startup.
• GemEnhancedCommandOptions.GemEnhancedCommandOptions Constructor — Initializes a new instance with default values.
• GemEnhancedCommandResultInfo.GemEnhancedCommandResultInfo Constructor — Describes an enhanced remote command request received by the equipment (S2F49) or an enhanced remote command reply received by the host (S2F50).
• GemEnhancedCommandState.GemEnhancedCommandState Constructor — Represents a snapshot of the counters of the configured enhanced remote command store.
• GemEnhancedObjectDefinition.GemEnhancedObjectDefinition Constructor — Defines one object (OBJSPEC) and the enhanced remote commands it accepts.
• GemEnhancedObjectEntry.Dispose Method — Releases the native name item.
• GemEnhancedObjectInfo.GemEnhancedObjectInfo Constructor — Represents the metadata of one configured enhanced command object.
• GemEquipment.CancelProgramGrant Method — Withdraws the grant that an answered S7F1 request activated.
• GemEquipment.CaptureSpool Method — Stores a primary message in the spool if spooling is active and the message is selected.
• GemEquipment.CaptureSpoolAlarm Method — Builds an S5F1 (Alarm Report Send) as GemEquipment.PublishAlarm does and stores it in the spool instead of sending it.
• GemEquipment.CaptureSpoolEvent Method — Builds an S6F11 (Event Report Send) as GemEquipment.PublishEventWithData does and stores it in the spool instead of sending it.
• GemEquipment.ClearDataVariable Method — Removes the cached value of a data variable.
• GemEquipment.ClearReportBindings Method — Removes the explicit report variable bindings.
• GemEquipment.CompleteSpoolDelivery Method — Reports the application's verdict on a delivery and, on success, removes the delivered entry from the spool.
• GemEquipment.ConfigureAlarms Method — Installs the alarm store that backs S5F1 alarm reports and the automatic replies to S5F3, S5F5 and S5F7.
• GemEquipment.ConfigureCommands Method — Installs the remote command store used to validate received S2F41 (Host Command Send) requests.
• GemEquipment.ConfigureConstants Method — Installs the equipment constant store that answers S2F13, S2F29 and S2F15.
• GemEquipment.ConfigureDataVariables Method — Configures or replaces the equipment's data variable store.
• GemEquipment.ConfigureEnhancedCommands Method — Installs the enhanced remote command store used to validate received S2F49 (Enhanced Remote Command) requests.
• GemEquipment.ConfigureEventDirectory Method — Configures or replaces the equipment's collection event directory, which answers S1F23 (Collection Event Namelist Request).
• GemEquipment.ConfigureFixedCatalog Method — Installs a complete fixed report catalog and its explicit report variable bindings in one atomic step.
• GemEquipment.ConfigureLocalSpooling Method — Sets the local spooling policy and the streams and functions selected for spooling.
• GemEquipment.ConfigurePrograms Method — Installs the process program store and enables the stream 7 process program transactions.
• GemEquipment.ConfigureReportBindings Method — Configures or replaces the explicit bindings from report variable IDs (VIDs) to value sources.
• GemEquipment.ConfigureReports Method — Creates the equipment's event report store and registers its collection events.
• GemEquipment.ConfigureSpooling Method — Attaches a spool to the equipment, kept in memory or in a snapshot file.
• GemEquipment.ConfirmProgramReply Method — Accepts an unconfirmed installation so that its saved reply can be sent.
• GemEquipment.ConfirmSpoolReply Method — Accepts the unconfirmed persistence of a held spooling reply so that GemEquipment.RespondSpool can send it.
• GemEquipment.Create Method — Creates an HSMS endpoint and configures it as GEM equipment.
• GemEquipment.DeleteLocalPrograms Method — Deletes process programs from the local store.
• GemEquipment.GetAlarmAt Method — Gets the configured alarm at a position in registration order.
• GemEquipment.GetAlarmState Method — Gets the counters of the configured alarm store.
• GemEquipment.GetBindingAt Method — Gets the report variable binding at a position in stored order.
• GemEquipment.GetBindingState Method — Gets the current state of the report variable bindings.
• GemEquipment.GetCommandAt Method — Gets the configured remote command at a position in registration order.
• GemEquipment.GetCommandParameterAt Method — Gets one parameter definition of a configured remote command.
• GemEquipment.GetCommandState Method — Gets the counters of the configured remote command store.
• GemEquipment.GetConstant Method — Gets one field of a registered equipment constant.
• GemEquipment.GetConstantAt Method — Gets the ID and declared shape of the constant at a position in registration order.
• GemEquipment.GetConstantState Method — Gets the counters of the equipment constant store.
• GemEquipment.GetData Method — Gets one field of a data variable as a new item.
• GemEquipment.GetDataAt Method — Gets the shape and cache state of the data variable at a position in the store.
• GemEquipment.GetDataState Method — Gets the current counters of the equipment's data variable store.
• GemEquipment.GetDirectory Method — Gets one field of an event directory entry as a new item.
• GemEquipment.GetDirectoryAt Method — Gets the event ID and variable count of the directory entry at a position in stored order.
• GemEquipment.GetDirectoryState Method — Gets the current counters of the equipment's event directory.
• GemEquipment.GetEnhancedCommandAt Method — Gets one command definition of a configured enhanced command object.
• GemEquipment.GetEnhancedCommandParameterAt Method — Gets one parameter definition of a command of a configured enhanced command object.
• GemEquipment.GetEnhancedCommandState Method — Gets the counters of the configured enhanced remote command store.
• GemEquipment.GetEnhancedObjectAt Method — Gets the configured enhanced command object at a position in registration order.
• GemEquipment.GetEventAt Method — Gets the collection event at a position in the equipment's report store.
• GemEquipment.GetProgram Method — Gets a copy of the body of a stored process program.
• GemEquipment.GetProgramAt Method — Gets a copy of the stored process program at a position in the store.
• GemEquipment.GetProgramState Method — Gets the counters of the process program store.
• GemEquipment.GetReportAt Method — Gets the report definition at a position in the equipment's report store.
• GemEquipment.GetReportState Method — Gets the current counters of the equipment's event report store.
• GemEquipment.GetReportValue Method — Gets a copy of the current value that a report variable ID resolves to.
• GemEquipment.GetSpoolCatalogAt Method — Gets one entry of the spool catalog.
• GemEquipment.GetSpoolEntryAt Method — Gets a copy of one stored spool entry.
• GemEquipment.GetSpoolEntryCapturedAt Method — Gets the capture time recorded for a spool entry.
• GemEquipment.GetSpoolSelectionAt Method — Gets one stream selection of the current spooling configuration.
• GemEquipment.GetSpoolState Method — Gets the counters, policy and flags of the spool.
• GemEquipment.GetStatus Method — Gets a copy of the current value of a registered status variable.
• GemEquipment.GetStatusIdAt Method — Gets the ID of the status variable at a position in registration order.
• GemEquipment.GetStatusMetadata Method — Gets the name and units of a registered status variable.
• GemEquipment.GrantProgram Method — Sends S7F1 (Process Program Load Inquire) to ask the peer to accept a process program.
• GemEquipment.ObserveAlarm Method — Records the current active state of a configured alarm without sending a message.
• GemEquipment.OperatorOffline Method — Switches the equipment to GemControlState.EquipmentOffline, as the operator's OFF-LINE switch does.
• GemEquipment.OperatorOnline Method — Starts an operator request to go on-line by sending S1F1 (Are You There) to the host.
• GemEquipment.PublishAlarm Method — Sends an S5F1 (Alarm Report Send) message with the current state of a configured alarm.
• GemEquipment.PublishEvent Method — Sends an event report (S6F11) for an enabled collection event; an event without linked reports is sent with an empty report list.
• GemEquipment.PublishEventWithData Method — Sends an event report (S6F11) whose data variable values come from the supplied samples first and from the cached values second.
• GemEquipment.PurgeSpool Method — Removes every stored entry from the spool.
• GemEquipment.PutProgram Method — Stores a process program in the local store.
• GemEquipment.RegisterStatus Method — Registers a status variable that the equipment reports in S1F4 and S1F12.
• GemEquipment.RequestProgram Method — Sends S7F5 (Process Program Request) for a process program of the peer.
• GemEquipment.RespondCommand Method — Sends the S2F42 (Host Command Acknowledge) reply to a received S2F41 remote command.
• GemEquipment.RespondConstants Method — Sends the S2F16 (New Equipment Constant Acknowledge) reply to a received S2F15 request.
• GemEquipment.RespondEnhancedCommand Method — Sends the S2F50 (Enhanced Remote Command Acknowledge) reply to a received S2F49 request.
• GemEquipment.RespondProgram Method — Answers a received stream 7 process program request.
• GemEquipment.RespondReportQuery Method — Answers a received S6F15, S6F19 or S6F21 report query with S6F16, S6F20 or S6F22.
• GemEquipment.RespondSpool Method — Applies a spooling request received by the equipment and sends its reply: S2F44 for S2F43, S2F60 for S2F59 or S6F24 for S6F23.
• GemEquipment.ResyncPrograms Method — Synchronizes the parent directory of the storage file again.
• GemEquipment.ResyncSpool Method — Retries synchronizing the parent directory of the spool snapshot file.
• GemEquipment.RetrySpoolDequeue Method — Retries removing a delivered entry whose success was accepted but whose removal failed.
• GemEquipment.SendNextSpool Method — Sends the oldest stored entry as the next delivery of the current transmission run.
• GemEquipment.SendProgram Method — Sends S7F3 (Process Program Send) with a process program.
• GemEquipment.SetOnlineMode Method — Sets the operator's REMOTE/LOCAL switch.
• GemEquipment.StopSpoolTransmit Method — Ends the current transmission run and keeps the stored entries.
• GemEquipment.SyncSpool Method — Records the current communication and selection state for spooling and activates spooling while communication is down.
• GemEquipment.TryCopyAlarmAt Method — Copies the configured alarm at a position in registration order into a caller-supplied buffer.
• GemEquipment.TryCopyEventAt Method — Copies the collection event at a position in the equipment's report store into a caller buffer.
• GemEquipment.TryCopyReportAt Method — Copies the report definition at a position in the equipment's report store into a caller buffer.
• GemEquipment.TryCopyStatusMetadata Method — Copies the name and units of a registered status variable into caller buffers.
• GemEquipment.UpdateDataVariable Method — Replaces the cached value of a data variable.
• GemEquipment.UpdateStatus Method — Replaces the value of a registered status variable.
• GemEquipmentOptions.GemEquipmentOptions Constructor — Initializes a new instance with default values.
• GemEquipmentSpoolConfiguration.GemEquipmentSpoolConfiguration Constructor — Represents the spool that GemEquipmentWorker.StartWithSpoolingAsync attaches to the equipment.
• GemEquipmentWorker.CancelProgramGrantAsync Method — Queues GemEquipment.CancelProgramGrant on the worker thread.
• GemEquipmentWorker.CaptureSpoolAlarmAsync Method — Queues GemEquipment.CaptureSpoolAlarm on the worker thread.
• GemEquipmentWorker.CaptureSpoolAsync Method — Queues GemEquipment.CaptureSpool on the worker thread.
• GemEquipmentWorker.CaptureSpoolEventAsync Method — Queues GemEquipment.CaptureSpoolEvent on the worker thread.
• GemEquipmentWorker.ClearDataVariableAsync Method — Queues GemEquipment.ClearDataVariable on the worker thread.
• GemEquipmentWorker.CompleteSpoolDeliveryAsync Method — Queues GemEquipment.CompleteSpoolDelivery on the worker thread.
• GemEquipmentWorker.ConfirmProgramReplyAsync Method — Queues GemEquipment.ConfirmProgramReply on the worker thread.
• GemEquipmentWorker.ConfirmSpoolReplyAsync Method — Queues GemEquipment.ConfirmSpoolReply on the worker thread.
• GemEquipmentWorker.GetAlarmAtAsync Method — Queues GemEquipment.GetAlarmAt on the worker thread.
• GemEquipmentWorker.GetAlarmStateAsync Method — Queues GemEquipment.GetAlarmState on the worker thread.
• GemEquipmentWorker.GetBindingAtAsync Method — Queues GemEquipment.GetBindingAt on the worker thread.
• GemEquipmentWorker.GetBindingStateAsync Method — Queues GemEquipment.GetBindingState on the worker thread.
• GemEquipmentWorker.GetCommandAtAsync Method — Queues GemEquipment.GetCommandAt on the worker thread.
• GemEquipmentWorker.GetCommandParameterAtAsync Method — Queues GemEquipment.GetCommandParameterAt on the worker thread.
• GemEquipmentWorker.GetCommandStateAsync Method — Queues GemEquipment.GetCommandState on the worker thread.
• GemEquipmentWorker.GetConstantAsync Method — Queues GemEquipment.GetConstant on the worker thread.
• GemEquipmentWorker.GetConstantAtAsync Method — Queues GemEquipment.GetConstantAt on the worker thread.
• GemEquipmentWorker.GetConstantStateAsync Method — Queues GemEquipment.GetConstantState on the worker thread.
• GemEquipmentWorker.GetDataAsync Method — Queues GemEquipment.GetData on the worker thread.
• GemEquipmentWorker.GetDataAtAsync Method — Queues GemEquipment.GetDataAt on the worker thread.
• GemEquipmentWorker.GetDataStateAsync Method — Queues GemEquipment.GetDataState on the worker thread.
• GemEquipmentWorker.GetDirectoryAsync Method — Queues GemEquipment.GetDirectory on the worker thread.
• GemEquipmentWorker.GetDirectoryAtAsync Method — Queues GemEquipment.GetDirectoryAt on the worker thread.
• GemEquipmentWorker.GetDirectoryStateAsync Method — Queues GemEquipment.GetDirectoryState on the worker thread.
• GemEquipmentWorker.GetEnhancedCommandAtAsync Method — Queues GemEquipment.GetEnhancedCommandAt on the worker thread.
• GemEquipmentWorker.GetEnhancedCommandParameterAtAsync Method — Queues GemEquipment.GetEnhancedCommandParameterAt on the worker thread.
• GemEquipmentWorker.GetEnhancedCommandStateAsync Method — Queues GemEquipment.GetEnhancedCommandState on the worker thread.
• GemEquipmentWorker.GetEnhancedObjectAtAsync Method — Queues GemEquipment.GetEnhancedObjectAt on the worker thread.
• GemEquipmentWorker.GetEventAtAsync Method — Queues GemEquipment.GetEventAt on the worker thread.
• GemEquipmentWorker.GetProgramAsync Method — Queues GemEquipment.GetProgram on the worker thread.
• GemEquipmentWorker.GetProgramAtAsync Method — Queues GemEquipment.GetProgramAt on the worker thread.
• GemEquipmentWorker.GetProgramStateAsync Method — Queues GemEquipment.GetProgramState on the worker thread.
• GemEquipmentWorker.GetReportAtAsync Method — Queues GemEquipment.GetReportAt on the worker thread.
• GemEquipmentWorker.GetReportStateAsync Method — Queues GemEquipment.GetReportState on the worker thread.
• GemEquipmentWorker.GetReportValueAsync Method — Queues GemEquipment.GetReportValue on the worker thread.
• GemEquipmentWorker.GetSpoolCatalogAtAsync Method — Queues GemEquipment.GetSpoolCatalogAt on the worker thread.
• GemEquipmentWorker.GetSpoolEntryAtAsync Method — Queues GemEquipment.GetSpoolEntryAt on the worker thread.
• GemEquipmentWorker.GetSpoolEntryCapturedAtAsync Method — Queues GemEquipment.GetSpoolEntryCapturedAt on the worker thread.
• GemEquipmentWorker.GetSpoolSelectionAtAsync Method — Queues GemEquipment.GetSpoolSelectionAt on the worker thread.
• GemEquipmentWorker.GetSpoolStateAsync Method — Queues GemEquipment.GetSpoolState on the worker thread.
• GemEquipmentWorker.GetStatusAsync Method — Queues GemEquipment.GetStatus on the worker thread.
• GemEquipmentWorker.GetStatusIdAtAsync Method — Queues GemEquipment.GetStatusIdAt on the worker thread.
• GemEquipmentWorker.GetStatusMetadataAsync Method — Queues GemEquipment.GetStatusMetadata on the worker thread.
• GemEquipmentWorker.GrantProgramAsync Method — Queues GemEquipment.GrantProgram on the worker thread.
• GemEquipmentWorker.ObserveAlarmAsync Method — Queues GemEquipment.ObserveAlarm on the worker thread.
• GemEquipmentWorker.OperatorOfflineAsync Method — Queues GemEquipment.OperatorOffline on the worker thread.
• GemEquipmentWorker.OperatorOnlineAsync Method — Queues GemEquipment.OperatorOnline on the worker thread to send S1F1 and attempt to go on-line.
• GemEquipmentWorker.PublishAlarmAsync Method — Queues GemEquipment.PublishAlarm on the worker thread.
• GemEquipmentWorker.PublishEventAsync Method — Queues GemEquipment.PublishEvent on the worker thread.
• GemEquipmentWorker.PublishEventWithDataAsync Method — Queues GemEquipment.PublishEventWithData on the worker thread.
• GemEquipmentWorker.RequestProgramAsync Method — Queues GemEquipment.RequestProgram on the worker thread.
• GemEquipmentWorker.RespondCommandAsync Method — Queues GemEquipment.RespondCommand on the worker thread.
• GemEquipmentWorker.RespondConstantsAsync Method — Queues GemEquipment.RespondConstants on the worker thread.
• GemEquipmentWorker.RespondEnhancedCommandAsync Method — Queues GemEquipment.RespondEnhancedCommand on the worker thread.
• GemEquipmentWorker.RespondProgramAsync Method — Queues GemEquipment.RespondProgram on the worker thread.
• GemEquipmentWorker.RespondReportQueryAsync Method — Queues GemEquipment.RespondReportQuery on the worker thread to answer a received S6F15, S6F19 or S6F21 report query.
• GemEquipmentWorker.RespondSpoolingAsync Method — Queues GemEquipment.RespondSpool on the worker thread.
• GemEquipmentWorker.ResyncProgramsAsync Method — Queues GemEquipment.ResyncPrograms on the worker thread.
• GemEquipmentWorker.ResyncSpoolingAsync Method — Queues GemEquipment.ResyncSpool on the worker thread.
• GemEquipmentWorker.RetrySpoolDequeueAsync Method — Queues GemEquipment.RetrySpoolDequeue on the worker thread.
• GemEquipmentWorker.SendNextSpoolAsync Method — Queues GemEquipment.SendNextSpool on the worker thread.
• GemEquipmentWorker.SendProgramAsync Method — Queues GemEquipment.SendProgram on the worker thread.
• GemEquipmentWorker.SetOnlineModeAsync Method — Queues GemEquipment.SetOnlineMode on the worker thread.
• GemEquipmentWorker.StartAsync Method — Starts an equipment worker whose endpoint is configured with status variables, reports, alarms, remote commands, enhanced remote commands and equipment constants.
• GemEquipmentWorker.StartAsync Method — Starts an equipment worker whose endpoint is configured with a collection event directory and optional status variables, report store, alarms, remote commands, enhanced remote commands, data variables and equipment constants.
• GemEquipmentWorker.StartAsync Method — Starts an equipment worker whose endpoint is configured with data variables and optional status variables, report store, alarms, remote commands, enhanced remote commands and equipment constants.
• GemEquipmentWorker.StartAsync Method — Starts an equipment worker whose endpoint is configured with status variables, reports, alarms, remote commands and enhanced remote commands.
• GemEquipmentWorker.StartAsync Method — Starts an equipment worker whose endpoint is configured with status variables, reports, alarms and remote commands.
• GemEquipmentWorker.StartAsync Method — Starts an equipment worker whose endpoint is configured with status variables, reports and alarms.
• GemEquipmentWorker.StartAsync Method — Starts an equipment worker whose endpoint is configured with initial status variables and an event report store.
• GemEquipmentWorker.StartAsync Method — Starts a polling thread that creates, configures and starts a GEM equipment endpoint.
• GemEquipmentWorker.StartWithFormattedProgramsAsync Method — Starts a polling thread that creates and configures a GEM equipment endpoint, enables formatted process program services on it and starts it.
• GemEquipmentWorker.StartWithProgramsAsync Method — Starts an equipment worker whose process program store is loaded with initial programs.
• GemEquipmentWorker.StartWithProgramsAsync Method — Starts an equipment worker with an empty process program store.
• GemEquipmentWorker.StartWithSpoolingAsync Method — Starts an equipment worker whose endpoint gets a spool before the transport starts.
• GemEquipmentWorker.StopSpoolTransmitAsync Method — Queues GemEquipment.StopSpoolTransmit on the worker thread.
• GemEquipmentWorker.SyncSpoolingAsync Method — Queues GemEquipment.SyncSpool on the worker thread.
• GemEquipmentWorker.UpdateDataVariableAsync Method — Queues GemEquipment.UpdateDataVariable on the worker thread.
• GemEquipmentWorker.UpdateStatusAsync Method — Queues GemEquipment.UpdateStatus on the worker thread.
• GemEvent.Dispose Method — Disposes GemEvent.Result and GemEvent.TransportEvent.
• GemEventDefinition.GemEventDefinition Constructor — Represents a collection event stored by the equipment, with its enable state and linked reports.
• GemEventDirectoryDefinition.GemEventDirectoryDefinition Constructor — Represents one collection event entry of an equipment's event directory.
• GemEventInfo.GemEventInfo Constructor — Represents the header fields of an event report (S6F11) that a host received.
• GemEventReport.GemEventReport Constructor — Represents one report inside a received event report (S6F11).
• GemFixedEventDefinition.GemFixedEventDefinition Constructor — One collection event of a fixed report catalog: its ID, its linked reports and its initial enable state.
• GemFormattedProgramCapabilityCommand.GemFormattedProgramCapabilityCommand Constructor — One command entry of the equipment's process capabilities catalog, sent in S7F22.
• GemFormattedProgramCapabilityCommandInfo.GemFormattedProgramCapabilityCommandInfo Constructor — Describes one command of S7F22 process capabilities data.
• GemFormattedProgramCapabilityInfo.GemFormattedProgramCapabilityInfo Constructor — Describes an S7F21/S7F22 process capabilities transaction held by a GemResult.
• GemFormattedProgramCapabilityOptions.GemFormattedProgramCapabilityOptions Constructor — Limits for the S7F21/S7F22 process capabilities exchange and the equipment's capability catalog.
• GemFormattedProgramCommand.GemFormattedProgramCommand Constructor — One command of a formatted process program: a command code and its parameters.
• GemFormattedProgramCommandInfo.GemFormattedProgramCommandInfo Constructor — Describes one command of a received, stored, selected or executed formatted process program.
• GemFormattedProgramConfiguration.GemFormattedProgramConfiguration Constructor — The set of formatted process program services to enable on a GEM endpoint; a null option skips its service.
• GemFormattedProgramConfiguration.Configure Method — Configures every service whose options are set on a stopped endpoint.
• GemFormattedProgramDryRunInfo.GemFormattedProgramDryRunInfo Constructor — Summarizes a formatted process program dry run report.
• GemFormattedProgramDryRunIssueInfo.GemFormattedProgramDryRunIssueInfo Constructor — Describes one issue of a formatted process program dry run report.
• GemFormattedProgramDryRunOptions.GemFormattedProgramDryRunOptions Constructor — The policy version and limits of one formatted process program dry run.
• GemFormattedProgramDryRunReport.GetInfo Method — Gets the summary of the dry run report.
• GemFormattedProgramDryRunReport.GetIssueInfo Method — Gets one issue of the dry run report.
• GemFormattedProgramDryRunReport.GetModel Method — Gets the equipment model type (MDLN) of the evaluated program.
• GemFormattedProgramDryRunReport.GetProgramId Method — Gets the process program ID (PPID) of the evaluated program.
• GemFormattedProgramDryRunReport.GetProgramIdBytes Method — Gets the raw bytes of the evaluated program's PPID.
• GemFormattedProgramDryRunReport.GetSoftwareRevision Method — Gets the software revision (SOFTREV) of the evaluated program.
• GemFormattedProgramExecutionAction.GetCommandCode Method — Gets the command code (CCODE) of the command that a step action performs.
• GemFormattedProgramExecutionAction.GetInfo Method — Gets the description of the action.
• GemFormattedProgramExecutionAction.GetModel Method — Gets the equipment model type (MDLN) of the program that a start action starts.
• GemFormattedProgramExecutionAction.GetParameter Method — Gets one parameter (PPARM) of the command that a step action performs.
• GemFormattedProgramExecutionAction.GetProgramId Method — Gets the process program ID (PPID) of the program that a start action starts.
• GemFormattedProgramExecutionAction.GetSoftwareRevision Method — Gets the software revision (SOFTREV) of the program that a start action starts.
• GemFormattedProgramExecutionActionInfo.GemFormattedProgramExecutionActionInfo Constructor — Describes an action that a formatted process program execution asks the application to perform.
• GemFormattedProgramExecutionActionToken.GemFormattedProgramExecutionActionToken Constructor — Identifies one action that a formatted process program execution asks the application to perform.
• GemFormattedProgramExecutionInfo.GemFormattedProgramExecutionInfo Constructor — Summarizes the equipment's formatted process program execution at the time of a snapshot.
• GemFormattedProgramExecutionSnapshot.GetApplicationDetailBytes Method — Gets the detail bytes that the application passed with its terminal report.
• GemFormattedProgramExecutionSnapshot.GetCommandCode Method — Gets the command code (CCODE) of one command of the executed program.
• GemFormattedProgramExecutionSnapshot.GetCommandInfo Method — Gets the parameter count and the command code format of one command of the executed program.
• GemFormattedProgramExecutionSnapshot.GetInfo Method — Gets the execution state captured by the snapshot.
• GemFormattedProgramExecutionSnapshot.GetModel Method — Gets the equipment model type (MDLN) of the executed program.
• GemFormattedProgramExecutionSnapshot.GetParameter Method — Gets one parameter (PPARM) of one command of the executed program.
• GemFormattedProgramExecutionSnapshot.GetProgramId Method — Gets the process program ID (PPID) of the executed program.
• GemFormattedProgramExecutionSnapshot.GetSoftwareRevision Method — Gets the software revision (SOFTREV) of the executed program.
• GemFormattedProgramExecutionStart.GemFormattedProgramExecutionStart Constructor — The result of GemFormattedPrograms.StartExecution: the token of the new execution and its start action.
• GemFormattedProgramExecutionStart.Dispose Method — Releases the native memory of GemFormattedProgramExecutionStart.Action.
• GemFormattedProgramExecutionToken.GemFormattedProgramExecutionToken Constructor — Identifies one formatted process program execution of an equipment endpoint.
• GemFormattedProgramInfo.GemFormattedProgramInfo Constructor — Describes an S7F27/S7F28 process program verification send held by a GemResult.
• GemFormattedProgramIssue.GemFormattedProgramIssue Constructor — One issue of an S7F27 process program verification report.
• GemFormattedProgramOptions.GemFormattedProgramOptions Constructor — Limits for S7F27/S7F28 process program verification sends.
• GemFormattedProgramPayload.GemFormattedProgramPayload Constructor — A complete formatted process program: its identifier, model, software revision and commands.
• GemFormattedProgramQueryInfo.GemFormattedProgramQueryInfo Constructor — Describes an S7F25/S7F26 formatted process program request held by a GemResult.
• GemFormattedProgramQueryOptions.GemFormattedProgramQueryOptions Constructor — Limits for S7F25/S7F26 formatted process program requests and the equipment's program store.
• GemFormattedProgramSelectionInfo.GemFormattedProgramSelectionInfo Constructor — Describes the equipment's formatted process program selection at the time of a snapshot.
• GemFormattedProgramSelectionSnapshot.GetCommandCode Method — Gets the command code (CCODE) of one command of the selected program.
• GemFormattedProgramSelectionSnapshot.GetCommandInfo Method — Gets the parameter count and the command code format of one command of the selected program.
• GemFormattedProgramSelectionSnapshot.GetId Method — Gets the process program ID (PPID) of the selected program.
• GemFormattedProgramSelectionSnapshot.GetInfo Method — Gets the selection state captured by the snapshot.
• GemFormattedProgramSelectionSnapshot.GetModel Method — Gets the equipment model type (MDLN) of the selected program.
• GemFormattedProgramSelectionSnapshot.GetParameter Method — Gets one parameter (PPARM) of one command of the selected program.
• GemFormattedProgramSelectionSnapshot.GetSoftwareRevision Method — Gets the software revision (SOFTREV) of the selected program.
• GemFormattedProgramSelectionToken.GemFormattedProgramSelectionToken Constructor — Identifies the equipment's current formatted process program selection.
• GemFormattedProgramStoreEntryInfo.GemFormattedProgramStoreEntryInfo Constructor — Describes one process program of a formatted process program store snapshot.
• GemFormattedProgramStoreInfo.GemFormattedProgramStoreInfo Constructor — Describes the equipment's formatted process program store.
• GemFormattedProgramStoreSnapshot.GetEntryCommandCode Method — Gets the command code (CCODE) of one command of a stored program.
• GemFormattedProgramStoreSnapshot.GetEntryCommandInfo Method — Gets the parameter count and the command code format of one command of a stored program.
• GemFormattedProgramStoreSnapshot.GetEntryId Method — Gets the process program ID (PPID) of one stored program.
• GemFormattedProgramStoreSnapshot.GetEntryInfo Method — Gets the description of one stored program.
• GemFormattedProgramStoreSnapshot.GetEntryModel Method — Gets the equipment model type (MDLN) of one stored program.
• GemFormattedProgramStoreSnapshot.GetEntryParameter Method — Gets one parameter (PPARM) of one command of a stored program.
• GemFormattedProgramStoreSnapshot.GetEntrySoftwareRevision Method — Gets the software revision (SOFTREV) of one stored program.
• GemFormattedProgramStoreSnapshot.GetSnapshotInfo Method — Gets the store information captured by the snapshot.
• GemFormattedProgramTransferInfo.GemFormattedProgramTransferInfo Constructor — Describes an S7F23/S7F24 formatted process program send held by a GemResult.
• GemFormattedProgramTransferOptions.GemFormattedProgramTransferOptions Constructor — Limits for S7F23/S7F24 formatted process program sends.
• GemFormattedProgramVerificationNegotiationInfo.GemFormattedProgramVerificationNegotiationInfo Constructor — Describes an S7F29/S7F30 process program verification negotiation held by a GemResult.
• GemFormattedProgramVerificationNegotiationOptions.GemFormattedProgramVerificationNegotiationOptions Constructor — Limits for the S7F29/S7F30 process program verification inquire and grant that precedes an S7F27 verification send.
• GemFormattedProgramVerificationRequestInfo.GemFormattedProgramVerificationRequestInfo Constructor — Describes an S7F31/S7F32 verification request held by a GemResult.
• GemFormattedProgramVerificationRequestOptions.GemFormattedProgramVerificationRequestOptions Constructor — Limits for S7F31/S7F32 verification requests.
• GemFormattedPrograms.CancelExecution Method — Requests the cancellation of a running execution as a cancel action.
• GemFormattedPrograms.ClearCapabilities Method — Removes the equipment's process capabilities catalog.
• GemFormattedPrograms.ClearSelection Method — Clears the current program selection.
• GemFormattedPrograms.CompleteExecution Method — Reports the final outcome of a running execution and ends it.
• GemFormattedPrograms.ConfigureCapabilities Method — Enables the S7F21/S7F22 process capabilities service and, on equipment, its local capability catalog.
• GemFormattedPrograms.ConfigureQueries Method — Enables the S7F25/S7F26 formatted process program request service and, on equipment, the local formatted program store, selection and execution tracking.
• GemFormattedPrograms.ConfigureTransfers Method — Enables the S7F23/S7F24 formatted process program send service.
• GemFormattedPrograms.ConfigureVerificationNegotiation Method — Enables the S7F29/S7F30 verification inquire and grant negotiation that precedes an S7F27 verification send.
• GemFormattedPrograms.ConfigureVerificationReports Method — Enables the S7F27/S7F28 process program verification report service.
• GemFormattedPrograms.ConfigureVerificationRequests Method — Enables the S7F31/S7F32 verification request service.
• GemFormattedPrograms.DryRun Method — Analyzes the selected program against the equipment's capability catalog without executing it.
• GemFormattedPrograms.GetActionToken Method — Gets the token that identifies an execution action, for GemFormattedPrograms.SubmitActionResult.
• GemFormattedPrograms.GetExecutionSnapshot Method — Gets a snapshot of the equipment's formatted program execution tracker.
• GemFormattedPrograms.GetSelectionSnapshot Method — Gets a snapshot of the current program selection.
• GemFormattedPrograms.GetStoreInfo Method — Gets the revision, usage and limits of the equipment's local formatted program store.
• GemFormattedPrograms.GetStoreSnapshot Method — Gets a copy of every program in the equipment's local formatted program store.
• GemFormattedPrograms.PrepareVerification Method — Prepares an S7F27 verification report for the S7F29/S7F30 negotiation without sending anything.
• GemFormattedPrograms.PutProgram Method — Writes a program to the equipment's local formatted program store.
• GemFormattedPrograms.RemoveProgram Method — Removes a program from the equipment's local formatted program store.
• GemFormattedPrograms.RemoveQuery Method — Removes a program from the equipment's local formatted program store.
• GemFormattedPrograms.ReplaceCapabilities Method — Replaces the equipment's process capabilities catalog that answers S7F21.
• GemFormattedPrograms.RespondCapabilityQuery Method — Answers a received S7F21 with an S7F22 (Process Capabilities Data) built from the local catalog.
• GemFormattedPrograms.RespondQuery Method — Answers a received S7F25 with an S7F26 (Formatted Process Program Data) from the local store.
• GemFormattedPrograms.RespondTransfer Method — Answers a received S7F23 with an S7F24 (Formatted Process Program Acknowledge).
• GemFormattedPrograms.RespondTransferAndStore Method — Answers a received S7F23 with an S7F24 and, in the same step, writes the received program to the local store.
• GemFormattedPrograms.RespondVerification Method — Answers a received S7F29 with an S7F30 (Process Program Verification Grant).
• GemFormattedPrograms.RespondVerificationReport Method — Answers a received S7F27 verification report with S7F28 (Process Program Verification Acknowledge).
• GemFormattedPrograms.RespondVerificationRequest Method — Answers a received S7F31 with an S7F32 (Verification Request Acknowledge).
• GemFormattedPrograms.RetryVerification Method — Sends the S7F27 of a granted verification negotiation when the automatic send after the grant failed.
• GemFormattedPrograms.RetryVerificationResponse Method — Sends again the S7F30 reply that an earlier GemFormattedPrograms.RespondVerification could not queue.
• GemFormattedPrograms.SeedQuery Method — Adds a program to the equipment's local formatted program store, or replaces the stored program with the same PPID.
• GemFormattedPrograms.SelectProgram Method — Selects a stored program for a dry run and execution.
• GemFormattedPrograms.StartExecution Method — Starts tracking the execution of the selected formatted program and returns its first action, a start action.
• GemFormattedPrograms.StepExecution Method — Requests the next command of a running execution as a step action.
• GemFormattedPrograms.SubmitActionResult Method — Reports the application's result for the pending start, step or cancel action.
• GemFormattedPrograms.SubmitCapabilityQuery Method — Sends an S7F21 (Process Capabilities Request) to the equipment.
• GemFormattedPrograms.SubmitPreparedVerification Method — Sends the S7F29 (Process Program Verification Inquire) of a prepared verification report.
• GemFormattedPrograms.SubmitQuery Method — Sends an S7F25 (Formatted Process Program Request) to the equipment.
• GemFormattedPrograms.SubmitTransfer Method — Sends an S7F23 (Formatted Process Program Send) to the equipment.
• GemFormattedPrograms.SubmitVerificationReport Method — Sends an S7F27 (Process Program Verification Send) report to the host.
• GemFormattedPrograms.SubmitVerificationRequest Method — Sends an S7F31 (Verification Request Send) to the equipment.
• GemFormattedPrograms.ValidateSelection Method — Checks that a selection is still valid for execution and returns a snapshot of the selected program.
• GemFormattedProgramsWorker.CancelExecutionAsync Method — Queues GemFormattedPrograms.CancelExecution to run on the worker's polling thread.
• GemFormattedProgramsWorker.ClearCapabilitiesAsync Method — Queues GemFormattedPrograms.ClearCapabilities to run on the worker's polling thread.
• GemFormattedProgramsWorker.ClearSelectionAsync Method — Queues GemFormattedPrograms.ClearSelection to run on the worker's polling thread.
• GemFormattedProgramsWorker.CompleteExecutionAsync Method — Queues GemFormattedPrograms.CompleteExecution to run on the worker's polling thread.
• GemFormattedProgramsWorker.ConfigureCapabilitiesAsync Method — Queues GemFormattedPrograms.ConfigureCapabilities to run on the worker's polling thread.
• GemFormattedProgramsWorker.ConfigureQueriesAsync Method — Queues GemFormattedPrograms.ConfigureQueries to run on the worker's polling thread.
• GemFormattedProgramsWorker.ConfigureTransfersAsync Method — Queues GemFormattedPrograms.ConfigureTransfers to run on the worker's polling thread.
• GemFormattedProgramsWorker.ConfigureVerificationNegotiationAsync Method — Queues GemFormattedPrograms.ConfigureVerificationNegotiation to run on the worker's polling thread.
• GemFormattedProgramsWorker.ConfigureVerificationReportsAsync Method — Queues GemFormattedPrograms.ConfigureVerificationReports to run on the worker's polling thread.
• GemFormattedProgramsWorker.ConfigureVerificationRequestsAsync Method — Queues GemFormattedPrograms.ConfigureVerificationRequests to run on the worker's polling thread.
• GemFormattedProgramsWorker.DryRunAsync Method — Queues GemFormattedPrograms.DryRun to run on the worker's polling thread.
• GemFormattedProgramsWorker.GetExecutionSnapshotAsync Method — Queues GemFormattedPrograms.GetExecutionSnapshot to run on the worker's polling thread.
• GemFormattedProgramsWorker.GetSelectionSnapshotAsync Method — Queues GemFormattedPrograms.GetSelectionSnapshot to run on the worker's polling thread.
• GemFormattedProgramsWorker.GetStoreInfoAsync Method — Queues GemFormattedPrograms.GetStoreInfo to run on the worker's polling thread.
• GemFormattedProgramsWorker.GetStoreSnapshotAsync Method — Queues GemFormattedPrograms.GetStoreSnapshot to run on the worker's polling thread.
• GemFormattedProgramsWorker.PrepareVerificationAsync Method — Queues GemFormattedPrograms.PrepareVerification to run on the worker's polling thread.
• GemFormattedProgramsWorker.PutProgramAsync Method — Queues GemFormattedPrograms.PutProgram to run on the worker's polling thread.
• GemFormattedProgramsWorker.RemoveProgramAsync Method — Queues GemFormattedPrograms.RemoveProgram to run on the worker's polling thread.
• GemFormattedProgramsWorker.RemoveQueryAsync Method — Queues GemFormattedPrograms.RemoveQuery to run on the worker's polling thread.
• GemFormattedProgramsWorker.ReplaceCapabilitiesAsync Method — Queues GemFormattedPrograms.ReplaceCapabilities to run on the worker's polling thread.
• GemFormattedProgramsWorker.RespondCapabilityQueryAsync Method — Queues GemFormattedPrograms.RespondCapabilityQuery to run on the worker's polling thread.
• GemFormattedProgramsWorker.RespondQueryAsync Method — Queues GemFormattedPrograms.RespondQuery to run on the worker's polling thread.
• GemFormattedProgramsWorker.RespondTransferAndStoreAsync Method — Queues GemFormattedPrograms.RespondTransferAndStore to run on the worker's polling thread.
• GemFormattedProgramsWorker.RespondTransferAsync Method — Queues GemFormattedPrograms.RespondTransfer to run on the worker's polling thread.
• GemFormattedProgramsWorker.RespondVerificationAsync Method — Queues GemFormattedPrograms.RespondVerification to run on the worker's polling thread.
• GemFormattedProgramsWorker.RespondVerificationReportAsync Method — Queues GemFormattedPrograms.RespondVerificationReport to run on the worker's polling thread.
• GemFormattedProgramsWorker.RespondVerificationRequestAsync Method — Queues GemFormattedPrograms.RespondVerificationRequest to run on the worker's polling thread.
• GemFormattedProgramsWorker.RetryVerificationAsync Method — Queues GemFormattedPrograms.RetryVerification to run on the worker's polling thread.
• GemFormattedProgramsWorker.RetryVerificationResponseAsync Method — Queues GemFormattedPrograms.RetryVerificationResponse to run on the worker's polling thread.
• GemFormattedProgramsWorker.SeedQueryAsync Method — Queues GemFormattedPrograms.SeedQuery to run on the worker's polling thread.
• GemFormattedProgramsWorker.SelectProgramAsync Method — Queues GemFormattedPrograms.SelectProgram to run on the worker's polling thread.
• GemFormattedProgramsWorker.StartExecutionAsync Method — Queues GemFormattedPrograms.StartExecution to run on the worker's polling thread.
• GemFormattedProgramsWorker.StepExecutionAsync Method — Queues GemFormattedPrograms.StepExecution to run on the worker's polling thread.
• GemFormattedProgramsWorker.SubmitActionResultAsync Method — Queues GemFormattedPrograms.SubmitActionResult to run on the worker's polling thread.
• GemFormattedProgramsWorker.SubmitCapabilityQueryAsync Method — Queues GemFormattedPrograms.SubmitCapabilityQuery to run on the worker's polling thread.
• GemFormattedProgramsWorker.SubmitPreparedVerificationAsync Method — Queues GemFormattedPrograms.SubmitPreparedVerification to run on the worker's polling thread.
• GemFormattedProgramsWorker.SubmitQueryAsync Method — Queues GemFormattedPrograms.SubmitQuery to run on the worker's polling thread.
• GemFormattedProgramsWorker.SubmitTransferAsync Method — Queues GemFormattedPrograms.SubmitTransfer to run on the worker's polling thread.
• GemFormattedProgramsWorker.SubmitVerificationReportAsync Method — Queues GemFormattedPrograms.SubmitVerificationReport to run on the worker's polling thread.
• GemFormattedProgramsWorker.SubmitVerificationRequestAsync Method — Queues GemFormattedPrograms.SubmitVerificationRequest to run on the worker's polling thread.
• GemFormattedProgramsWorker.ValidateSelectionAsync Method — Queues GemFormattedPrograms.ValidateSelection to run on the worker's polling thread.
• GemHost.AcknowledgeAlarm Method — Sends the S5F2 (Alarm Report Acknowledge) reply to a received S5F1 alarm report.
• GemHost.AcknowledgeEvent Method — Sends S6F12 (Event Report Acknowledge) for an event report received from the equipment.
• GemHost.AreYouOnline Method — Sends S1F1 (Are You There) to the equipment.
• GemHost.CancelProgramGrant Method — Withdraws the grant that an answered S7F1 request activated.
• GemHost.ChangeConstants Method — Sends S2F15 (New Equipment Constant Send) with new equipment constant values.
• GemHost.ConfigurePrograms Method — Installs the process program store and enables the stream 7 process program transactions.
• GemHost.ConfigureSpoolHost Method — Enables the host spooling requests and sets their limits.
• GemHost.ConfirmProgramReply Method — Accepts an unconfirmed installation so that its saved reply can be sent.
• GemHost.Create Method — Creates an HSMS endpoint and configures it as a GEM host.
• GemHost.DefineReports Method — Sends S2F33 (Define Report) to the equipment.
• GemHost.DeleteLocalPrograms Method — Deletes process programs from the local store.
• GemHost.DeletePrograms Method — Sends S7F17 (Delete Process Program Send) to delete process programs on the equipment.
• GemHost.EnableAlarm Method — Sends an S5F3 (Enable/Disable Alarm Send) request for one alarm.
• GemHost.EnableEvents Method — Sends S2F37 (Enable/Disable Event Report) to the equipment.
• GemHost.EnhancedRemoteCommand Method — Sends an S2F49 (Enhanced Remote Command) request.
• GemHost.GetProgram Method — Gets a copy of the body of a stored process program.
• GemHost.GetProgramAt Method — Gets a copy of the stored process program at a position in the store.
• GemHost.GetProgramState Method — Gets the counters of the process program store.
• GemHost.GrantProgram Method — Sends S7F1 (Process Program Load Inquire) to ask the peer to accept a process program.
• GemHost.LinkReports Method — Sends S2F35 (Link Event Report) to the equipment.
• GemHost.PutProgram Method — Stores a process program in the local store.
• GemHost.QueryRemoteSpooling Method — Sends S2F59 to request the equipment's current spooling selection.
• GemHost.RemoteCommand Method — Sends an S2F41 (Host Command Send) remote command request.
• GemHost.RequestAlarmList Method — Sends an S5F5 (List Alarms Request) for selected alarms or for all alarms.
• GemHost.RequestAnnotatedQuery Method — Sends S6F21 (Annotated Individual Report Request) for a report.
• GemHost.RequestConstantMetadata Method — Sends S2F29 (Equipment Constant Namelist Request) for equipment constant metadata.
• GemHost.RequestConstantValues Method — Sends S2F13 (Equipment Constant Request) for equipment constant values.
• GemHost.RequestDataDirectory Method — Sends S1F21 (Data Variable Namelist Request) to the equipment.
• GemHost.RequestDirectory Method — Sends S1F21 (Data Variable Namelist Request) or S1F23 (Collection Event Namelist Request) to the equipment.
• GemHost.RequestEnabledAlarmList Method — Sends an S5F7 (List Enabled Alarm Request) for the alarms whose reporting is enabled.
• GemHost.RequestEventDirectory Method — Sends S1F23 (Collection Event Namelist Request) to the equipment.
• GemHost.RequestEventQuery Method — Sends S6F15 (Event Report Request) for a collection event.
• GemHost.RequestIndividualQuery Method — Sends S6F19 (Individual Report Request) for a report.
• GemHost.RequestOffline Method — Sends S1F15 (Request Off-line) to the equipment.
• GemHost.RequestOnline Method — Sends S1F17 (Request On-line) to the equipment.
• GemHost.RequestProgram Method — Sends S7F5 (Process Program Request) for a process program of the peer.
• GemHost.RequestProgramDirectory Method — Sends the header-only S7F19 (Current EPPD Request) for the equipment's process program list.
• GemHost.RequestReportQuery Method — Sends an S6 report query to the equipment.
• GemHost.RequestSpoolConfiguration Method — Sends S2F43 (Reset Spooling Streams and Functions) to set the equipment's spooling selection.
• GemHost.RequestSpooledData Method — Sends S6F23 (Request Spooled Data) to make the equipment transmit or purge its spool.
• GemHost.RequestStatusNames Method — Sends S1F11 (Status Variable Namelist Request) for status variable names and units.
• GemHost.RequestStatusValues Method — Sends S1F3 (Selected Equipment Status Request) for status variable values.
• GemHost.RespondProgram Method — Answers a received stream 7 process program request.
• GemHost.ResyncPrograms Method — Synchronizes the parent directory of the storage file again.
• GemHost.SendProgram Method — Sends S7F3 (Process Program Send) with a process program.
• GemHostOptions.GemHostOptions Constructor — Initializes a new instance with default values.
• GemHostWorker.AcknowledgeAlarmAsync Method — Queues GemHost.AcknowledgeAlarm on the worker thread.
• GemHostWorker.AcknowledgeEventAsync Method — Queues GemHost.AcknowledgeEvent on the worker thread.
• GemHostWorker.AreYouOnlineAsync Method — Queues GemHost.AreYouOnline on the worker thread to send S1F1 (Are You There).
• GemHostWorker.CancelProgramGrantAsync Method — Queues GemHost.CancelProgramGrant on the worker thread.
• GemHostWorker.ChangeConstantsAsync Method — Queues GemHost.ChangeConstants on the worker thread.
• GemHostWorker.ConfirmProgramReplyAsync Method — Queues GemHost.ConfirmProgramReply on the worker thread.
• GemHostWorker.DefineReportsAsync Method — Queues GemHost.DefineReports on the worker thread.
• GemHostWorker.DeleteProgramsAsync Method — Queues GemHost.DeletePrograms on the worker thread.
• GemHostWorker.EnableAlarmAsync Method — Queues GemHost.EnableAlarm on the worker thread.
• GemHostWorker.EnableEventsAsync Method — Queues GemHost.EnableEvents on the worker thread.
• GemHostWorker.EnhancedRemoteCommandAsync Method — Queues GemHost.EnhancedRemoteCommand on the worker thread.
• GemHostWorker.GetProgramAsync Method — Queues GemHost.GetProgram on the worker thread.
• GemHostWorker.GetProgramAtAsync Method — Queues GemHost.GetProgramAt on the worker thread.
• GemHostWorker.GetProgramStateAsync Method — Queues GemHost.GetProgramState on the worker thread.
• GemHostWorker.GrantProgramAsync Method — Queues GemHost.GrantProgram on the worker thread.
• GemHostWorker.LinkReportsAsync Method — Queues GemHost.LinkReports on the worker thread.
• GemHostWorker.QueryRemoteSpoolingAsync Method — Queues GemHost.QueryRemoteSpooling on the worker thread.
• GemHostWorker.RemoteCommandAsync Method — Queues GemHost.RemoteCommand on the worker thread.
• GemHostWorker.RequestAlarmListAsync Method — Queues GemHost.RequestAlarmList on the worker thread.
• GemHostWorker.RequestAnnotatedQueryAsync Method — Queues GemHost.RequestAnnotatedQuery on the worker thread to send S6F21.
• GemHostWorker.RequestConstantMetadataAsync Method — Queues GemHost.RequestConstantMetadata on the worker thread.
• GemHostWorker.RequestConstantValuesAsync Method — Queues GemHost.RequestConstantValues on the worker thread.
• GemHostWorker.RequestDirectoryAsync Method — Queues GemHost.RequestDirectory on the worker thread.
• GemHostWorker.RequestEnabledAlarmListAsync Method — Queues GemHost.RequestEnabledAlarmList on the worker thread.
• GemHostWorker.RequestEventQueryAsync Method — Queues GemHost.RequestEventQuery on the worker thread to send S6F15.
• GemHostWorker.RequestIndividualQueryAsync Method — Queues GemHost.RequestIndividualQuery on the worker thread to send S6F19.
• GemHostWorker.RequestOfflineAsync Method — Queues GemHost.RequestOffline on the worker thread to send S1F15 (Request Off-line).
• GemHostWorker.RequestOnlineAsync Method — Queues GemHost.RequestOnline on the worker thread to send S1F17 (Request On-line).
• GemHostWorker.RequestProgramAsync Method — Queues GemHost.RequestProgram on the worker thread.
• GemHostWorker.RequestProgramDirectoryAsync Method — Queues GemHost.RequestProgramDirectory on the worker thread.
• GemHostWorker.RequestReportQueryAsync Method — Queues GemHost.RequestReportQuery on the worker thread to send an S6 report query.
• GemHostWorker.RequestSpoolConfigurationAsync Method — Queues GemHost.RequestSpoolConfiguration on the worker thread.
• GemHostWorker.RequestSpooledDataAsync Method — Queues GemHost.RequestSpooledData on the worker thread.
• GemHostWorker.RequestStatusNamesAsync Method — Queues GemHost.RequestStatusNames on the worker thread to send S1F11 for status variable names and units.
• GemHostWorker.RequestStatusValuesAsync Method — Queues GemHost.RequestStatusValues on the worker thread to send S1F3 for status variable values.
• GemHostWorker.RespondProgramAsync Method — Queues GemHost.RespondProgram on the worker thread.
• GemHostWorker.ResyncProgramsAsync Method — Queues GemHost.ResyncPrograms on the worker thread.
• GemHostWorker.SendProgramAsync Method — Queues GemHost.SendProgram on the worker thread.
• GemHostWorker.StartAsync Method — Starts a polling thread that creates and starts a GEM host endpoint.
• GemHostWorker.StartWithFormattedProgramsAsync Method — Starts a polling thread that creates a GEM host endpoint, enables formatted process program services on it and starts it.
• GemHostWorker.StartWithProgramsAsync Method — Starts a host worker whose process program store is loaded with initial programs.
• GemHostWorker.StartWithProgramsAsync Method — Starts a host worker with an empty process program store.
• GemHostWorker.StartWithSpoolingAsync Method — Starts a host worker whose endpoint can send spooling requests.
• GemLinkSpec.GemLinkSpec Constructor — Represents one event link that a host sends in S2F35 (Link Event Report).
• GemOwnedSnapshot.Dispose Method — Releases the snapshot's native memory.
• GemProgramConfiguration.GemProgramConfiguration Constructor — Represents the process program store that a worker installs at startup.
• GemProgramDefinition.GemProgramDefinition Constructor — Represents a process program that a worker stores at startup.
• GemProgramEntry.Dispose Method — Releases GemProgramEntry.Id and GemProgramEntry.Body.
• GemProgramInfo.GemProgramInfo Constructor — Represents the state of a received stream 7 process program request or reply.
• GemProgramOptions.GemProgramOptions Constructor — Initializes a new instance with default values.
• GemProgramState.GemProgramState Constructor — Represents the counters of a process program store.
• GemProgramWriteInfo.GemProgramWriteInfo Constructor — Represents the outcome of a local process program change.
• GemQueryInfo.GemQueryInfo Constructor — Represents the report query details of a GemResult.
• GemQueryReportInfo.GemQueryReportInfo Constructor — Represents one report of an S6F16 event report reply.
• GemQueryValue.Dispose Method — Releases GemQueryValue.Value.
• GemReportBinding.GemReportBinding Constructor — Represents a binding from a report variable ID (VID) to the source of its value.
• GemReportBindingEntry.Dispose Method — Releases the GemReportBindingEntry.ConstantId item, if any.
• GemReportConfiguration.GemReportConfiguration Constructor — Represents the event report store that a GemEquipmentWorker configures when it starts.
• GemReportDefinition.GemReportDefinition Constructor — Represents a report definition: a report ID and its ordered variable IDs.
• GemReportOptions.GemReportOptions Constructor — Initializes a new instance with default values.
• GemReportSpec.GemReportSpec Constructor — Represents one report definition that a host sends in S2F33 (Define Report).
• GemReportState.GemReportState Constructor — Represents the current counters of an equipment's event report store.
• GemResult.Dispose Method — Releases the native result.
• GemResult.GetAlarmAt Method — Gets one alarm entry of the alarm report or alarm list carried by the result.
• GemResult.GetAlarmInfo Method — Gets the summary of the alarm report or alarm list carried by the result.
• GemResult.GetBody Method — Gets a copy of the SECS-II body captured with the result.
• GemResult.GetCommandInfo Method — Gets the summary of the remote command request or reply carried by the result.
• GemResult.GetCommandIssue Method — Gets one parameter acknowledgement (CPNAME and CPACK) of a remote command result.
• GemResult.GetCommandName Method — Gets the remote command name (RCMD) of a received S2F41 request.
• GemResult.GetCommandParameter Method — Gets one parameter of a received S2F41 request.
• GemResult.GetConstantChange Method — Gets one ECID/ECV pair of a received S2F15 request.
• GemResult.GetConstantChangeInfo Method — Gets the processing state of a received S2F15 request or S2F16 reply.
• GemResult.GetConstantMetadata Method — Gets one field of an entry of a received S2F30 (Equipment Constant Namelist) reply.
• GemResult.GetConstantValue Method — Gets one entry of a received S2F14 (Equipment Constant Data) reply.
• GemResult.GetDirectory Method — Gets one field of a row in a received namelist reply (S1F22 or S1F24) as a new item.
• GemResult.GetDirectoryAt Method — Gets the ID and variable count of one row in a received namelist reply (S1F22 or S1F24).
• GemResult.GetEnhancedCommandAcknowledgements Method — Gets the parameter acknowledgement list of an enhanced remote command result.
• GemResult.GetEnhancedCommandInfo Method — Gets the summary of the enhanced remote command request or reply carried by the result.
• GemResult.GetEnhancedCommandName Method — Gets the remote command name (RCMD) of a received S2F49 request.
• GemResult.GetEnhancedCommandObject Method — Gets the object specifier (OBJSPEC) of a received S2F49 request.
• GemResult.GetEnhancedCommandParameter Method — Gets one parameter of a received S2F49 request.
• GemResult.GetEventInfo Method — Gets the header fields of an event report (S6F11) received by a host.
• GemResult.GetEventReport Method — Gets the report ID and value count of one report in a received event report (S6F11).
• GemResult.GetEventValue Method — Gets a copy of one variable value (V) from a report in a received event report (S6F11).
• GemResult.GetFormattedProgramCapabilityCommandCode Method — Gets the command code (CCODE) of one command of the process capabilities data.
• GemResult.GetFormattedProgramCapabilityCommandInfo Method — Gets the description of one command of the process capabilities data.
• GemResult.GetFormattedProgramCapabilityCommandName Method — Gets the command name (CNAME) of one command of the process capabilities data.
• GemResult.GetFormattedProgramCapabilityDependencyAt Method — Gets one value of a dependency list of one command of the process capabilities data.
• GemResult.GetFormattedProgramCapabilityInfo Method — Gets the S7F21/S7F22 process capabilities information of this result.
• GemResult.GetFormattedProgramCapabilityModel Method — Gets the equipment model type (MDLN) of the process capabilities data.
• GemResult.GetFormattedProgramCapabilityParameter Method — Gets one parameter description of one command of the process capabilities data.
• GemResult.GetFormattedProgramCapabilitySoftwareRevision Method — Gets the software revision (SOFTREV) of the process capabilities data.
• GemResult.GetFormattedProgramId Method — Gets the process program ID (PPID) of the S7F27 verification report.
• GemResult.GetFormattedProgramInfo Method — Gets the S7F27/S7F28 process program verification information of this result.
• GemResult.GetFormattedProgramIssueAt Method — Gets one issue of the S7F27 verification report.
• GemResult.GetFormattedProgramQueryCommandCode Method — Gets the command code (CCODE) of one command of the returned formatted process program.
• GemResult.GetFormattedProgramQueryCommandInfo Method — Gets the parameter count and the command code format of one command of the returned formatted process program.
• GemResult.GetFormattedProgramQueryId Method — Gets the process program ID (PPID) that the S7F25 requested.
• GemResult.GetFormattedProgramQueryInfo Method — Gets the S7F25/S7F26 formatted process program request information of this result.
• GemResult.GetFormattedProgramQueryModel Method — Gets the equipment model type (MDLN) of the returned formatted process program.
• GemResult.GetFormattedProgramQueryParameter Method — Gets one parameter (PPARM) of one command of the returned formatted process program.
• GemResult.GetFormattedProgramQuerySoftwareRevision Method — Gets the software revision (SOFTREV) of the returned formatted process program.
• GemResult.GetFormattedProgramTransferCommandCode Method — Gets the command code (CCODE) of one command of the received formatted process program.
• GemResult.GetFormattedProgramTransferCommandInfo Method — Gets the parameter count and the command code format of one command of the received formatted process program.
• GemResult.GetFormattedProgramTransferId Method — Gets the process program ID (PPID) of the received formatted process program.
• GemResult.GetFormattedProgramTransferInfo Method — Gets the S7F23/S7F24 formatted process program send information of this result.
• GemResult.GetFormattedProgramTransferModel Method — Gets the equipment model type (MDLN) of the received formatted process program.
• GemResult.GetFormattedProgramTransferParameter Method — Gets one parameter (PPARM) of one command of the received formatted process program.
• GemResult.GetFormattedProgramTransferSoftwareRevision Method — Gets the software revision (SOFTREV) of the received formatted process program.
• GemResult.GetFormattedProgramVerificationNegotiationInfo Method — Gets the S7F29/S7F30 process program verification negotiation information of this result.
• GemResult.GetFormattedProgramVerificationRequestCommandCode Method — Gets the command code (CCODE) of one command of the received formatted process program.
• GemResult.GetFormattedProgramVerificationRequestCommandInfo Method — Gets the parameter count and the command code format of one command of the received formatted process program.
• GemResult.GetFormattedProgramVerificationRequestId Method — Gets the process program ID (PPID) of the received formatted process program.
• GemResult.GetFormattedProgramVerificationRequestInfo Method — Gets the S7F31/S7F32 verification request information of this result.
• GemResult.GetFormattedProgramVerificationRequestModel Method — Gets the equipment model type (MDLN) of the received formatted process program.
• GemResult.GetFormattedProgramVerificationRequestParameter Method — Gets one parameter (PPARM) of one command of the received formatted process program.
• GemResult.GetFormattedProgramVerificationRequestSoftwareRevision Method — Gets the software revision (SOFTREV) of the received formatted process program.
• GemResult.GetInfo Method — Gets the summary of the result: kind, outcome, transaction, codes, token and GEM state.
• GemResult.GetProgramBody Method — Gets a copy of the PPBODY of a received S7F3 request or S7F6 reply.
• GemResult.GetProgramId Method — Gets a copy of a PPID of a process program result.
• GemResult.GetProgramInfo Method — Gets the state of a received stream 7 process program request or reply.
• GemResult.GetProgramItem Method — Gets a copy of a PPID or the PPBODY of a process program result.
• GemResult.GetQueryInfo Method — Gets the report query details of a received query or a query reply.
• GemResult.GetQueryReport Method — Gets one report of an S6F16 event report reply.
• GemResult.GetQueryValue Method — Gets one value of a report query reply.
• GemResult.GetSpoolError Method — Gets one stream error of an S2F44 received by the host.
• GemResult.GetSpoolInfo Method — Gets the spooling details of a spooling request, reply or delivery result.
• GemResult.GetSpoolSelection Method — Gets one stream selection of an S2F43 received by the equipment or of an S2F60 received by the host.
• GemResult.GetStatusName Method — Gets one entry of a validated S1F12 status variable name list.
• GemResult.GetStatusValue Method — Gets one status variable value of a validated S1F4 reply.
• GemResult.TryCopyAlarmAt Method — Copies one alarm entry of the alarm report or alarm list into a caller-supplied buffer.
• GemResult.TryCopyStatusName Method — Copies one entry of a validated S1F12 status variable name list into caller buffers.
• GemResultInfo.GemResultInfo Constructor — Represents the summary of a GemResult.
• GemSpoolEntry.Dispose Method — Releases the body.
• GemSpoolEntryInfo.GemSpoolEntryInfo Constructor — Represents the header of one stored spool entry.
• GemSpoolHostOptions.GemSpoolHostOptions Constructor — Initializes a new instance with default values.
• GemSpoolInfo.GemSpoolInfo Constructor — Represents the spooling details of a GemResult.
• GemSpoolMessageKey.GemSpoolMessageKey Constructor — Represents a primary message (stream and function) in the equipment spool catalog.
• GemSpoolOptions.GemSpoolOptions Constructor — Initializes a new instance with default values.
• GemSpoolPolicy.GemSpoolPolicy Constructor — Initializes a new instance with default values.
• GemSpoolResultError.Dispose Method — Releases GemSpoolResultError.Functions.
• GemSpoolResultSelection.Dispose Method — Releases GemSpoolResultSelection.Functions.
• GemSpoolSelection.GemSpoolSelection Constructor — Represents the functions of one stream that are selected for spooling.
• GemSpoolState.GemSpoolState Constructor — Represents the counters, policy and flags of the equipment spool.
• GemSpoolWriteResult.GemSpoolWriteResult Constructor — Represents the outcome of an equipment spool operation that can change the spool.
• GemState.GemState Constructor — Represents a snapshot of the GEM state of an endpoint.
• GemStatusName.GemStatusName Constructor — Represents the name and units of a status variable.
• GemStatusValue.Dispose Method — Releases GemStatusValue.Value.
• GemStatusVariable.GemStatusVariable Constructor — Represents a status variable that GemEquipmentWorker registers on its endpoint at startup.
• GemWorker.BeginCommunicationAsync Method — Queues GemEndpoint.BeginCommunication on the worker thread to send S1F13.
• GemWorker.CancelAsync Method — Queues GemEndpoint.Cancel on the worker thread.
• GemWorker.DeselectAsync Method — Queues GemEndpoint.Deselect on the worker thread to send an HSMS Deselect.req control message.
• GemWorker.DisposeAsync Method — Stops the worker, releases the endpoint and waits for the worker thread to exit.
• GemWorker.GetLocalAddressAsync Method — Queues GemEndpoint.GetLocalAddress on the worker thread.
• GemWorker.GetStateAsync Method — Queues GemEndpoint.GetState on the worker thread.
• GemWorker.GetTransportStateAsync Method — Queues GemEndpoint.GetTransportState on the worker thread.
• GemWorker.IsPendingAsync Method — Queues GemEndpoint.IsPending on the worker thread.
• GemWorker.LinktestAsync Method — Queues GemEndpoint.Linktest on the worker thread to send an HSMS Linktest.req control message.
• GemWorker.ReadEventsAsync Method — Reads the GEM events produced by the worker thread, in order.
• GemWorker.ReplyRawAsync Method — Queues GemEndpoint.ReplyRaw on the worker thread to send a raw SECS-II reply.
• GemWorker.RequestRawAsync Method — Queues GemEndpoint.RequestRaw on the worker thread to send a raw SECS-II primary message.
• GemWorker.SelectAsync Method — Queues GemEndpoint.Select on the worker thread to send an HSMS Select.req control message.
• GemWorker.StopAsync Method — Queues a graceful stop of the transport on the worker thread.
• HsmsEndpoint.Cancel Method — Cancels an open transaction of this endpoint.
• HsmsEndpoint.Create Method — Creates an HSMS endpoint.
• HsmsEndpoint.Deselect Method — Sends Deselect.req to end the selected HSMS session without closing the connection.
• HsmsEndpoint.Dispose Method — Releases the native endpoint and closes its sockets.
• HsmsEndpoint.GetLocalAddress Method — Gets the local socket address, for example the port a passive endpoint actually listens on.
• HsmsEndpoint.GetState Method — Gets the endpoint's connection state.
• HsmsEndpoint.IsPending Method — Determines whether a transaction of this endpoint is still open.
• HsmsEndpoint.Linktest Method — Sends Linktest.req to check that the connection is alive.
• HsmsEndpoint.NextEvent Method — Takes the next queued event.
• HsmsEndpoint.Poll Method — Advances timers, connection handling and socket I/O.
• HsmsEndpoint.Reply Method — Queues the reply to a received primary message.
• HsmsEndpoint.Request Method — Queues a primary data message.
• HsmsEndpoint.Select Method — Sends Select.req to select the HSMS session.
• HsmsEndpoint.Start Method — Starts connecting (active) or listening (passive).
• HsmsEndpoint.Stop Method — Begins a graceful shutdown of the connection.
• HsmsEvent.DecodeBody Method — Decodes the body of a received message as a SECS-II item.
• HsmsEvent.Dispose Method — Releases the event's native data.
• HsmsEvent.GetBody Method — Copies the encoded SECS-II body of a received message.
• HsmsEvent.GetInfo Method — Gets the event's kind, header, token and kind-specific values.
• HsmsEvent.TryCopyBody Method — Copies the encoded SECS-II body into a caller-supplied span when it is large enough.
• HsmsEventInfo.HsmsEventInfo Constructor — Describes one HsmsEvent.
• HsmsHeader.HsmsHeader Constructor — The 10-byte HSMS message header of a received message.
• HsmsOptions.HsmsOptions Constructor — Initializes a new instance with default values.
• HsmsState.HsmsState Constructor — A snapshot of an HSMS endpoint's state.
• HsmsToken.HsmsToken Constructor — Identifies one transaction of an HSMS endpoint.
• HsmsWorker.CancelAsync Method — Cancels an open transaction on the worker thread.
• HsmsWorker.DeselectAsync Method — Queues Deselect.req on the worker thread.
• HsmsWorker.DisposeAsync Method — Stops the worker, closes the endpoint and waits for the worker thread to exit.
• HsmsWorker.GetLocalAddressAsync Method — Reads the endpoint's local socket address on the worker thread.
• HsmsWorker.GetStateAsync Method — Reads the endpoint's connection state on the worker thread.
• HsmsWorker.IsPendingAsync Method — Determines on the worker thread whether a transaction is still open.
• HsmsWorker.LinktestAsync Method — Queues Linktest.req on the worker thread.
• HsmsWorker.ReadEventsAsync Method — Reads the events produced by the endpoint, in order.
• HsmsWorker.ReplyAsync Method — Queues the reply to a received primary message on the worker thread.
• HsmsWorker.SelectAsync Method — Queues Select.req on the worker thread.
• HsmsWorker.StartAsync Method — Creates an HSMS endpoint on a new worker thread and starts it.
• HsmsWorker.StopAsync Method — Begins a graceful shutdown of the connection and of the worker.
• HsmsWorker.SubmitRequestAsync Method — Queues a primary data message on the worker thread.
• HsmsWorkerOptions.HsmsWorkerOptions Constructor — Initializes a new instance with default values.
• Secs1Event.Secs1Event Constructor — An event produced by a Secs1Worker.
• Secs1IoResult.Secs1IoResult Constructor — The result of a Secs1Read or Secs1Write callback.
• Secs1Message.Secs1Message Constructor — A SECS-I message: block header identity plus the message body.
• Secs1Options.Secs1Options Constructor — Line timing, retry and capacity options for a SECS-I (SEMI E4) endpoint.
• Secs1State.Secs1State Constructor — A snapshot of a SECS-I endpoint's lifecycle flags.
• Secs1Token.Secs1Token Constructor — Identifies one message submitted to a SECS-I endpoint.
• Secs1Worker.DisposeAsync Method — Stops the worker thread, which stops and destroys the native endpoint.
• Secs1Worker.GetStateAsync Method — Reads the endpoint's lifecycle flags on the worker thread.
• Secs1Worker.ReadEventsAsync Method — Reads the events produced by the endpoint, in order.
• Secs1Worker.ResetAsync Method — Clears a line fault so the endpoint can resume.
• Secs1Worker.RestartAsync Method — Starts a stopped endpoint again with a new generation.
• Secs1Worker.StartAsync Method — Creates a SECS-I endpoint on a new worker thread and starts it.
• Secs1Worker.StopAsync Method — Stops the endpoint and discards its runtime state, without invoking the callbacks.
• Secs1Worker.SubmitAsync Method — Queues a message for transmission on the serial line.
• Secs1WorkerOptions.Secs1WorkerOptions Constructor — Queue capacities and timing for a Secs1Worker.
• SecsItem.CreateList Method — Creates a list item from copies of existing items.
• SecsItem.Decode Method — Decodes exactly one encoded SECS-II item.
• SecsItem.Dispose Method — Releases the item's native memory.
• SecsItem.Encode Method — Encodes the item in SECS-II wire format.
• SecsItem.FromAscii Method — Creates an SecsFormat.Ascii item from text.
• SecsItem.FromBinary Method — Creates a SecsFormat.Binary item from raw bytes.
• SecsItem.FromBoolean Method — Creates a SecsFormat.Boolean item from Boolean values, one byte each (1 for true, 0 for false).
• SecsItem.FromF4 Method — Creates a SecsFormat.F4 item from Single IEEE 754 values, big-endian.
• SecsItem.FromF8 Method — Creates a SecsFormat.F8 item from Double IEEE 754 values, big-endian.
• SecsItem.FromI1 Method — Creates a SecsFormat.I1 item from SByte signed integers.
• SecsItem.FromI2 Method — Creates a SecsFormat.I2 item from Int16 signed integers, big-endian.
• SecsItem.FromI4 Method — Creates a SecsFormat.I4 item from Int32 signed integers, big-endian.
• SecsItem.FromI8 Method — Creates a SecsFormat.I8 item from Int64 signed integers, big-endian.
• SecsItem.FromJis8 Method — Creates a SecsFormat.Jis8 item from JIS-8 encoded bytes.
• SecsItem.FromU1 Method — Creates a SecsFormat.U1 item from Byte unsigned integers.
• SecsItem.FromU2 Method — Creates a SecsFormat.U2 item from UInt16 unsigned integers, big-endian.
• SecsItem.FromU4 Method — Creates a SecsFormat.U4 item from UInt32 unsigned integers, big-endian.
• SecsItem.FromU8 Method — Creates a SecsFormat.U8 item from UInt64 unsigned integers, big-endian.
• SecsItem.GetAscii Method — Reads the text of an ASCII item.
• SecsItem.GetBinary Method — Reads the values of a Binary item as raw bytes.
• SecsItem.GetBoolean Method — Reads the values of a Boolean item as Boolean values; any nonzero byte is true.
• SecsItem.GetChild Method — Copies one child of a list item.
• SecsItem.GetF4 Method — Reads the values of an F4 item as Single values.
• SecsItem.GetF8 Method — Reads the values of an F8 item as Double values.
• SecsItem.GetI1 Method — Reads the values of an I1 item as SByte values.
• SecsItem.GetI2 Method — Reads the values of an I2 item as Int16 values.
• SecsItem.GetI4 Method — Reads the values of an I4 item as Int32 values.
• SecsItem.GetI8 Method — Reads the values of an I8 item as Int64 values.
• SecsItem.GetInfo Method — Gets the item's format, element count, encoded size and tree shape.
• SecsItem.GetJis8 Method — Reads the values of a Jis8 item as its JIS-8 bytes, unchanged.
• SecsItem.GetPayload Method — Copies the raw payload bytes of a primitive item.
• SecsItem.GetU1 Method — Reads the values of a U1 item as Byte values.
• SecsItem.GetU2 Method — Reads the values of a U2 item as UInt16 values.
• SecsItem.GetU4 Method — Reads the values of a U4 item as UInt32 values.
• SecsItem.GetU8 Method — Reads the values of a U8 item as UInt64 values.
• SecsItem.Primitive Method — Creates a primitive item from its raw payload bytes.
• SecsItem.TryCopyPayload Method — Copies the raw payload bytes of a primitive item into a caller-supplied span when it is large enough.
• SecsItem.TryEncode Method — Encodes the item into a caller-supplied span when it is large enough.
• SecsLimits.SecsLimits Constructor — Initializes a set of SECS-II limits.
• Gem300Capability.Axis Property — The object area of the capability; each axis occurs at most once per profile.
• Gem300Capability.Id Property — The capability identifier: nonempty printable ASCII without spaces (bytes 0x21 through 0x7E), unique within its profile.
• Gem300Capability.Status Property — The declared status label.
• Gem300Capability.Verification Property — The verification label; the default is the only defined value.
• Gem300CapabilityCatalogInfo.CapabilityCount Property — The number of capabilities across all profiles.
• Gem300CapabilityCatalogInfo.IdentifierBytes Property — The total length, in bytes, of all profile and capability IDs.
• Gem300CapabilityCatalogInfo.ProfileCount Property — The number of profiles.
• Gem300CapabilityCatalogInfo.Revision Property — The catalog revision. It starts at 0 and increases by one for each replace or clear that changes the contents.
• Gem300CapabilityInfo.Axis Property — The Gem300Axis code: 1 process job, 2 carrier, 3 substrate or 4 control job.
• Gem300CapabilityInfo.IdLength Property — The length of the capability ID, in bytes.
• Gem300CapabilityInfo.Status Property — The Gem300Status label code that the application assigns: 1 planned, 2 model only or 3 experimental.
• Gem300CapabilityInfo.Verification Property — The Gem300Verification label code: 1, the only defined value.
• Gem300CapabilityOptions.MaxCapabilitiesPerProfile Property — The largest number of capabilities in one profile, at most 4: the capabilities of a profile must use distinct Gem300Axis values.
• Gem300CapabilityOptions.MaxCapabilityIdBytes Property — The longest capability ID, in bytes.
• Gem300CapabilityOptions.MaxProfileIdBytes Property — The longest profile ID, in bytes.
• Gem300CapabilityOptions.MaxProfiles Property — The largest number of profiles in the catalog.
• Gem300CapabilityOptions.MaxTotalCapabilities Property — The largest number of capabilities across all profiles.
• Gem300CapabilityOptions.MaxTotalIdentifierBytes Property — The largest total length, in bytes, of all profile and capability IDs.
• Gem300CapabilityProfile.Capabilities Property — The capabilities in order: at least one and at most Gem300CapabilityOptions.MaxCapabilitiesPerProfile.
• Gem300CapabilityProfile.Id Property — The profile identifier: nonempty printable ASCII without spaces (bytes 0x21 through 0x7E), unique within the catalog.
• Gem300CapabilityProfileInfo.CapabilityCount Property — The number of capabilities in the profile.
• Gem300CapabilityProfileInfo.IdLength Property — The length of the profile ID, in bytes.
• Gem300CatalogChange.Changed Property — Whether the contents changed; when false, Gem300CatalogChange.Revision is unchanged.
• Gem300CatalogChange.Revision Property — The catalog revision after the call.
• GemAlarmChange.Active Property — The active state of the alarm after the observation.
• GemAlarmChange.Changed Property — Whether the observation changed the active state of the alarm.
• GemAlarmChange.EventId Property — The collection event ID (CEID) mapped to the transition (the set event when the alarm became active, the clear event when it cleared), or null when the state did not change or no event is mapped.
• GemAlarmChange.Id Property — The alarm ID (ALID).
• GemAlarmChange.ReportingEnabled Property — Whether alarm reporting is currently enabled for the alarm.
• GemAlarmConfiguration.Definitions Property — The alarm definitions in registration order.
• GemAlarmConfiguration.Options Property — The alarm store limits.
• GemAlarmDefinition.Category Property — The alarm category, 1 through 63. It is sent in the low bits of the alarm code (ALCD); bit 8 of ALCD carries the active state.
• GemAlarmDefinition.ClearEvent Property — The optional collection event ID (CEID) that GemEquipment.ObserveAlarm returns when the alarm clears. It must be one of the configured report event IDs.
• GemAlarmDefinition.Id Property — The alarm ID (ALID). IDs must be unique within the store.
• GemAlarmDefinition.SetEvent Property — The optional collection event ID (CEID) that GemEquipment.ObserveAlarm returns when the alarm becomes active. It must be one of the event IDs configured with GemEquipment.ConfigureReports.
• GemAlarmDefinition.Text Property — The alarm text (ALTX). It must contain only ASCII characters and be at most the smaller of GemAlarmOptions.MaxTextBytes and 120 bytes. An empty text is allowed.
• GemAlarmEntry.Info Property — The alarm state and metadata.
• GemAlarmEntry.Text Property — The alarm text (ALTX).
• GemAlarmInfo.Active Property — Whether the last observed state of the alarm is active (set).
• GemAlarmInfo.Category Property — The alarm category, 1 through 63.
• GemAlarmInfo.ClearEvent Property — The collection event ID (CEID) mapped to the clear transition, if any.
• GemAlarmInfo.Enabled Property — Whether alarm reporting is enabled. Alarms start disabled; the host enables them with S5F3.
• GemAlarmInfo.Id Property — The alarm ID (ALID).
• GemAlarmInfo.SetEvent Property — The collection event ID (CEID) mapped to the set transition, if any.
• GemAlarmOptions.MaxAlarms Property — Gets the maximum number of alarm definitions. The value must be greater than zero.
• GemAlarmOptions.MaxTextBytes Property — Gets the maximum size, in bytes, of one alarm text (ALTX). The effective limit is the smaller of this value and 120 bytes.
• GemAlarmOptions.MaxTotalTextBytes Property — Gets the maximum combined size, in bytes, of all alarm texts (ALTX) in the store.
• GemAlarmResultInfo.Acknowledged Property — Whether GemHost.AcknowledgeAlarm has sent the S5F2 reply for the report.
• GemAlarmResultInfo.Count Property — The number of alarm entries: 1 for an alarm report (S5F1), or the number of entries in an S5F6 or S5F8 list.
• GemAlarmResultInfo.IsReport Property — Whether the result is a received alarm report (S5F1) rather than a list reply.
• GemAlarmResultInfo.ReplyExpected Property — Whether the alarm report requested a reply (W-bit set). Always false for list replies.
• GemAlarmState.ActiveCount Property — The number of alarms whose observed state is active (set).
• GemAlarmState.AlarmCount Property — The number of configured alarms.
• GemAlarmState.EnabledCount Property — The number of alarms whose reporting the host has enabled with S5F3.
• GemAlarmState.TextBytes Property — The combined size, in bytes, of all alarm texts.
• GemAlarmValue.Info Property — The alarm ID, category and active state from the wire.
• GemAlarmValue.Text Property — The alarm text (ALTX).
• GemAlarmValueInfo.Active Property — Whether bit 8 of the alarm code (ALCD) marks the alarm as active (set).
• GemAlarmValueInfo.Category Property — The alarm category taken from the low six bits of the alarm code (ALCD).
• GemAlarmValueInfo.Id Property — The alarm ID (ALID).
• GemBindingOptions.MaxBindings Property — Gets the maximum number of bindings.
• GemBindingOptions.MaxIdentifierBytes Property — Gets the maximum length, in bytes, of one ASCII constant identifier.
• GemBindingOptions.MaxTotalIdentifierBytes Property — Gets the maximum total length, in bytes, of all ASCII constant identifiers.
• GemBindingState.BindingCount Property — The number of bindings.
• GemBindingState.ExplicitMode Property — true when explicit bindings are configured, even an empty set; false when every VID resolves to the status variable with the same ID.
• GemBindingState.IdentifierBytes Property — The total length, in bytes, of all ASCII constant identifiers.
• GemCommandArgument.Name Property — Gets the parameter name (CPNAME) in its wire format.
• GemCommandArgument.Value Property — Gets the parameter value (CPVAL or CEPVAL).
• GemCommandConfiguration.Definitions Property — The command definitions in registration order.
• GemCommandConfiguration.Options Property — The command store limits.
• GemCommandDefinition.CompletionEvent Property — The optional collection event ID (CEID) returned in GemCommandReply.CompletionEvent when the reply carries HCACK 0 or 4. It must be one of the event IDs configured with GemEquipment.ConfigureReports.
• GemCommandDefinition.Name Property — The remote command name (RCMD): a nonempty ASCII item, or a scalar integer item from -128 through 255. Names must be unique. The item is read only during configuration.
• GemCommandDefinition.Parameters Property — The parameter definitions. Parameter names must be unique within the command.
• GemCommandDefinition.RequireOnlineRemote Property — Whether the command is accepted only in the online remote control state. Otherwise validation rejects it with HCACK 2 (cannot perform now).
• GemCommandEntry.Info Property — Gets the command metadata.
• GemCommandEntry.Name Property — Gets the remote command name (RCMD). A numeric name is returned as an I1 or U1 item, which may differ from the configured format.
• GemCommandError.Code Property — Gets the parameter acknowledge code (CPACK).
• GemCommandError.Name Property — Gets the parameter name (CPNAME).
• GemCommandInfo.CompletionEvent Property — The completion collection event ID (CEID), if any.
• GemCommandInfo.ParameterCount Property — The number of parameter definitions of the command.
• GemCommandInfo.RequireOnlineRemote Property — Whether the command requires the online remote control state.
• GemCommandIssue.Code Property — The parameter acknowledge code (CPACK), 1 through 3: 1 means the parameter name does not exist, 2 means the value is illegal, and 3 means the value format is illegal.
• GemCommandIssue.Name Property — The parameter name (CPNAME): an ASCII item or a scalar integer item.
• GemCommandOptions.MaxCommands Property — Gets the maximum number of remote command definitions. The value must be greater than zero.
• GemCommandOptions.MaxErrors Property — Gets the maximum number of parameter issues (CPACK entries) in a validation result or in a reply.
• GemCommandOptions.MaxIdentifierBytes Property — Gets the maximum size, in bytes, of one ASCII command or parameter name.
• GemCommandOptions.MaxParametersPerCommand Property — Gets the maximum number of parameters of one command definition and of one received S2F41 request.
• GemCommandOptions.MaxTotalIdentifierBytes Property — Gets the maximum combined size, in bytes, of all ASCII command and parameter names. Numeric names count as zero bytes.
• GemCommandOptions.MaxTotalParameters Property — Gets the maximum number of parameter definitions across all commands.
• GemCommandParameter.Name Property — The parameter name (CPNAME): an ASCII item or a scalar integer item. Integer names are sent as I8 or U8.
• GemCommandParameter.Value Property — The parameter value: CPVAL for S2F41, or CEPVAL for S2F49.
• GemCommandParameterDefinition.Format Property — The exact SECS-II format the value must have, or null to accept any allowed format. A value with another format is reported with CPACK 3. For S2F41 commands only Binary, Boolean, ASCII and integer formats are allowed; for S2F49 commands every format except JIS-8 is allowed.
• GemCommandParameterDefinition.MaxCount Property — The maximum element count of the value. It must not be less than MinCount. A longer value is reported with CPACK 2.
• GemCommandParameterDefinition.Maximum Property — The optional inclusive upper bound of every element of an integer value. It must not be less than Minimum. A value above the bound is reported with CPACK 2.
• GemCommandParameterDefinition.MinCount Property — The minimum element count of the value. A shorter value is reported with CPACK 2.
• GemCommandParameterDefinition.Minimum Property — The optional inclusive lower bound of every element of an integer value. Bounds require an integer Format. A value below the bound is reported with CPACK 2.
• GemCommandParameterDefinition.Name Property — The parameter name (CPNAME): an ASCII item, or a scalar integer item (I1, I2, I4, I8, U1, U2, U4 or U8). Positive signed and unsigned names compare equal. The item is read only during configuration.
• GemCommandParameterDefinition.Required Property — Whether the parameter must be present. A missing required parameter is reported with CPACK 2.
• GemCommandParameterEntry.Info Property — Gets the parameter validation rules.
• GemCommandParameterEntry.Name Property — Gets the parameter name (CPNAME). A numeric name is returned as an I8 or U8 item, which may differ from the configured format.
• GemCommandParameterInfo.Format Property — The required SECS-II format of the value, or null when any allowed format is accepted.
• GemCommandParameterInfo.MaxCount Property — The maximum element count of the value.
• GemCommandParameterInfo.Maximum Property — The inclusive upper bound of integer elements, if any.
• GemCommandParameterInfo.MinCount Property — The minimum element count of the value.
• GemCommandParameterInfo.Minimum Property — The inclusive lower bound of integer elements, if any.
• GemCommandParameterInfo.Required Property — Whether the parameter must be present.
• GemCommandReply.Acknowledgement Property — The host command acknowledge code (HCACK) that was sent.
• GemCommandReply.CompletionEvent Property — The completion collection event ID (CEID) of the command when the sent HCACK is 0 or 4; otherwise null. Publish the event separately when the work completes.
• GemCommandResultInfo.CompletionEvent Property — The completion collection event ID (CEID) of an accepted request, or null.
• GemCommandResultInfo.IsRequest Property — true for an equipment-side S2F41 request; false for a host-side S2F42 reply.
• GemCommandResultInfo.IssueCount Property — For a request, the number of parameter issues found by validation on receipt; for a reply, the number of received parameter acknowledgements (CPACK entries).
• GemCommandResultInfo.ParameterCount Property — The number of parameters in the received request, or 0 for a reply.
• GemCommandResultInfo.Responded Property — Whether GemEquipment.RespondCommand has sent the S2F42 reply. Always false for a reply.
• GemCommandResultInfo.ValidationAccepted Property — Whether the built-in validation accepted the request on receipt. Always false for a reply.
• GemCommandResultInfo.ValidationAcknowledgement Property — For a request, the HCACK chosen by validation on receipt: 0 when accepted, otherwise 1, 2 or 3. For a reply, the HCACK received from the equipment.
• GemCommandState.CommandCount Property — The number of configured commands.
• GemCommandState.IdentifierBytes Property — The combined size, in bytes, of all ASCII command and parameter names. Numeric names count as zero bytes.
• GemCommandState.TotalParameters Property — The number of parameter definitions across all commands.
• GemConstantChange.Id Property — The equipment constant ID (ECID): an ASCII item or a scalar integer item.
• GemConstantChange.Value Property — The new value (ECV).
• GemConstantChangeEntry.Id Property — Gets the proposed equipment constant ID (ECID) in its wire format.
• GemConstantChangeEntry.Original Property — Gets the current value of the constant when the request was received, or null when the ID is unknown.
• GemConstantChangeEntry.Value Property — Gets the proposed new value (ECV) in its wire format.
• GemConstantChangeInfo.Applied Property — Whether a nonempty change was applied to the equipment constant store.
• GemConstantChangeInfo.ChangeCount Property — The number of ECID/ECV pairs in the received request; zero for a reply.
• GemConstantChangeInfo.IsRequest Property — true for an S2F15 request received by the equipment; false for an S2F16 reply received by the host, whose other fields are then zero.
• GemConstantChangeInfo.Responded Property — Whether the S2F16 reply was sent.
• GemConstantChangeInfo.ValidationAccepted Property — Whether the automatic receipt validation accepted all changes, so that the application decision is used.
• GemConstantChangeInfo.ValidationAcknowledgement Property — The EAC from the receipt validation: 0 when accepted, 1 when a constant does not exist, or 3 when a value is invalid, for example a wrong format or count, a value outside the bounds, a NaN or a duplicate ID. A rejected receipt is always answered with this code, whatever the application decides.
• GemConstantConfiguration.Definitions Property — The constant definitions in registration order.
• GemConstantConfiguration.Options Property — The constant store limits.
• GemConstantDefinition.Current Property — The initial value (ECV). Its format is the declared format of the constant; later changes must use the same format. JIS-8 items and NaN floating-point values are rejected, also inside lists.
• GemConstantDefinition.DefaultValue Property — The default value (ECDEF), or null when the constant has none. Must have the format of Current.
• GemConstantDefinition.Id Property — The equipment constant ID (ECID): an ASCII item (case-sensitive, may be empty) or a scalar integer item (I1 to I8 or U1 to U8 with one value). Positive signed and unsigned IDs with the same value are the same ID.
• GemConstantDefinition.MaxCount Property — The largest element count that a value of the constant may have; must not be less than MinCount.
• GemConstantDefinition.Maximum Property — The upper bound (ECMAX), or null for none. Must have the format of Current.
• GemConstantDefinition.MinCount Property — The smallest element count that a value of the constant may have.
• GemConstantDefinition.Minimum Property — The lower bound (ECMIN), or null for none. Must have the format of Current.
• GemConstantDefinition.Name Property — The constant name (ECNAME); ASCII only, may be empty.
• GemConstantDefinition.Units Property — The units (UNITS); ASCII only, may be empty.
• GemConstantEntry.Id Property — Gets the equipment constant ID (ECID); a stored integer ID may be returned as an I8 or U8 item.
• GemConstantEntry.Info Property — Gets the declared shape of the constant.
• GemConstantInfo.DefaultPresent Property — Whether the constant has a default value (ECDEF).
• GemConstantInfo.Format Property — The format of the current value, which every new value must use.
• GemConstantInfo.MaxCount Property — The largest element count a value may have.
• GemConstantInfo.MaximumPresent Property — Whether the constant has an upper bound (ECMAX).
• GemConstantInfo.MinCount Property — The smallest element count a value may have.
• GemConstantInfo.MinimumPresent Property — Whether the constant has a lower bound (ECMIN).
• GemConstantOptions.ItemLimits Property — Gets the SECS-II limits that every stored value must satisfy.
• GemConstantOptions.MaxChangesPerRequest Property — Gets the maximum number of ECID/ECV pairs that one received S2F15 request can carry.
• GemConstantOptions.MaxConstants Property — Gets the maximum number of equipment constants (ECIDs) the store can hold.
• GemConstantOptions.MaxIdentifierBytes Property — Gets the maximum length in bytes of an ASCII constant ID, in definitions and in received requests.
• GemConstantOptions.MaxMetadataBytes Property — Gets the maximum total bytes of all ASCII constant IDs, names (ECNAME) and units (UNITS) in the store.
• GemConstantOptions.MaxQueryIds Property — Gets the maximum number of IDs that one received S2F13 or S2F29 request can carry.
• GemConstantOptions.MaxValueBytes Property — Gets the maximum total encoded bytes of all current, default, minimum and maximum values in the store.
• GemConstantReply.Acknowledgement Property — The EAC (equipment acknowledge code) that was sent.
• GemConstantReply.Applied Property — Whether the new values replaced the store contents; false for a rejection and for an empty request.
• GemConstantState.ConstantCount Property — The number of registered constants.
• GemConstantState.MetadataBytes Property — The total bytes of ASCII IDs, names and units in use.
• GemConstantState.ValueBytes Property — The total encoded bytes of current, default, minimum and maximum values in use.
• GemConstantValue.Id Property — Gets the requested equipment constant ID (ECID) in its original request format, or null when the request asked for all constants and the reply carries no IDs.
• GemConstantValue.Value Property — Gets the reported value (ECV). An empty list alone does not prove that the ID is unknown to the equipment.
• GemDataConfiguration.BindingOptions Property — The capacity limits of the report bindings, or null for no explicit bindings. Supply it together with Bindings.
• GemDataConfiguration.Bindings Property — The report variable bindings, or null for none. Supply it together with BindingOptions.
• GemDataConfiguration.Definitions Property — The data variable definitions. The worker validates them and copies names, units and cached values when it is started.
• GemDataConfiguration.Options Property — The capacity limits of the data variable store.
• GemDataDefinition.Cached Property — The initial cached value, or null for no value. An absent value differs from an empty one. The configuring call copies the item; the caller keeps ownership.
• GemDataDefinition.Format Property — The SECS-II format that every value of the variable must have at the top level.
• GemDataDefinition.Id Property — The data variable ID. Report bindings refer to it with GemDataSourceKind.Data.
• GemDataDefinition.MaxCount Property — The maximum top-level count (SecsInfo.Count) of a value; must not be less than MinCount.
• GemDataDefinition.MinCount Property — The minimum top-level count (SecsInfo.Count) of a value.
• GemDataDefinition.Name Property — The ASCII name. The equipment reports it as DVVALNAME in S1F22 for VIDs bound to this variable.
• GemDataDefinition.Units Property — The ASCII units (UNITS); may be empty.
• GemDataInfo.CachedPresent Property — true when the variable has a cached value.
• GemDataInfo.Format Property — The SECS-II format that every value must have.
• GemDataInfo.Id Property — The data variable ID.
• GemDataInfo.MaxCount Property — The maximum top-level count of a value.
• GemDataInfo.MinCount Property — The minimum top-level count of a value.
• GemDataOptions.ItemLimits Property — Gets the SECS-II item limits that every cached value and data sample must satisfy.
• GemDataOptions.MaxMetadataBytes Property — Gets the maximum total size, in bytes, of all ASCII names and units.
• GemDataOptions.MaxSampleBytes Property — Gets the maximum total encoded size, in bytes, of the data samples supplied with one event report.
• GemDataOptions.MaxSamplesPerEvent Property — Gets the maximum number of data samples supplied with one event report.
• GemDataOptions.MaxValueBytes Property — Gets the maximum total encoded size, in bytes, of all cached values.
• GemDataOptions.MaxVariables Property — Gets the maximum number of data variables in the store.
• GemDataSample.Id Property — The data variable ID (not the VID).
• GemDataSample.Value Property — The value. It must match the variable's format and count range. The publishing call copies it; the caller keeps ownership.
• GemDataState.MetadataBytes Property — The total size, in bytes, of all names and units.
• GemDataState.ValueBytes Property — The total encoded size, in bytes, of all cached values.
• GemDataState.VariableCount Property — The number of data variables.
• GemDirectoryConfiguration.Definitions Property — The event entries. The worker validates them and copies names and variable IDs when it is started.
• GemDirectoryConfiguration.Options Property — The capacity limits of the directory.
• GemDirectoryEntryInfo.Id Property — The entry ID: the CEID of an event entry, or the VID of a data variable entry in a received S1F22.
• GemDirectoryEntryInfo.VariableCount Property — The number of variable IDs of an event entry; 0 for data variable entries.
• GemDirectoryOptions.MaxEvents Property — Gets the maximum number of event entries.
• GemDirectoryOptions.MaxMetadataBytes Property — Gets the maximum total length, in bytes, of all event names.
• GemDirectoryOptions.MaxNameBytes Property — Gets the maximum length, in bytes, of one ASCII event name.
• GemDirectoryOptions.MaxTotalVariables Property — Gets the maximum number of variable IDs across all event entries.
• GemDirectoryOptions.MaxVariablesPerEvent Property — Gets the maximum number of variable IDs (VIDs) in one event entry.
• GemDirectoryState.Configured Property — true when a directory is configured, even an empty one; false when none is.
• GemDirectoryState.EventCount Property — The number of event entries.
• GemDirectoryState.MetadataBytes Property — The total length, in bytes, of all event names.
• GemDirectoryState.TotalVariables Property — The number of variable IDs across all event entries.
• GemEndpoint.FormattedPrograms Property — Gets the formatted process program services of this endpoint.
• GemEnhancedCommandConfiguration.Objects Property — The object definitions in registration order.
• GemEnhancedCommandConfiguration.Options Property — The enhanced command store limits.
• GemEnhancedCommandOptions.ItemLimits Property — Gets the SECS-II limits that every received parameter value must satisfy. Every limit must be greater than zero.
• GemEnhancedCommandOptions.MaxCommandsPerObject Property — Gets the maximum number of command definitions of one object.
• GemEnhancedCommandOptions.MaxErrors Property — Gets the maximum number of nonzero parameter acknowledgement codes in a validation result or in a reply.
• GemEnhancedCommandOptions.MaxIdentifierBytes Property — Gets the maximum size, in bytes, of one ASCII command or parameter name.
• GemEnhancedCommandOptions.MaxObjectBytes Property — Gets the maximum size, in bytes, of one object name, configured or received.
• GemEnhancedCommandOptions.MaxObjects Property — Gets the maximum number of object definitions (OBJSPEC).
• GemEnhancedCommandOptions.MaxParametersPerCommand Property — Gets the maximum number of parameters of one command definition and of one received S2F49 request.
• GemEnhancedCommandOptions.MaxRequestValueBytes Property — Gets the maximum combined encoded size, in bytes, of all parameter values (CEPVAL) in one received S2F49 request.
• GemEnhancedCommandOptions.MaxTotalCommands Property — Gets the maximum number of command definitions across all objects.
• GemEnhancedCommandOptions.MaxTotalIdentifierBytes Property — Gets the maximum combined size, in bytes, of all ASCII command and parameter names. Numeric names count as zero bytes.
• GemEnhancedCommandOptions.MaxTotalObjectBytes Property — Gets the maximum combined size, in bytes, of all configured object names.
• GemEnhancedCommandOptions.MaxTotalParameters Property — Gets the maximum number of parameter definitions across all commands.
• GemEnhancedCommandResultInfo.CompletionEvent Property — The completion collection event ID (CEID) of an accepted request, or null.
• GemEnhancedCommandResultInfo.DataId Property — The data ID (DATAID) of the request, or 0 for a reply.
• GemEnhancedCommandResultInfo.IsRequest Property — true for an equipment-side S2F49 request; false for a host-side S2F50 reply.
• GemEnhancedCommandResultInfo.IssueCount Property — The number of outer entries of the parameter acknowledgement list: the validation errors found on receipt for a request (0 when accepted), or the received entries for a reply.
• GemEnhancedCommandResultInfo.ParameterCount Property — The number of parameters in the received request, or 0 for a reply.
• GemEnhancedCommandResultInfo.Responded Property — Whether GemEquipment.RespondEnhancedCommand has sent the S2F50 reply. Always false for a reply.
• GemEnhancedCommandResultInfo.ValidationAccepted Property — Whether the built-in validation accepted the request on receipt. Always false for a reply.
• GemEnhancedCommandResultInfo.ValidationAcknowledgement Property — For a request, the HCACK chosen by validation on receipt: 0 when accepted, otherwise 1, 2, 3 or 6. For a reply, the HCACK received from the equipment.
• GemEnhancedCommandState.CommandCount Property — The number of command definitions across all objects.
• GemEnhancedCommandState.IdentifierBytes Property — The combined size, in bytes, of all ASCII command and parameter names.
• GemEnhancedCommandState.ObjectCount Property — The number of configured objects.
• GemEnhancedCommandState.TotalObjectBytes Property — The combined size, in bytes, of all object names.
• GemEnhancedCommandState.TotalParameters Property — The number of parameter definitions across all commands.
• GemEnhancedObjectDefinition.Commands Property — The command definitions of the object. The rules of GemCommandDefinition apply, except that parameter values may use every format except JIS-8.
• GemEnhancedObjectDefinition.Name Property — The object name: an ASCII item matched exactly and case-sensitively. An empty name is allowed when registered explicitly. Object names must be unique.
• GemEnhancedObjectEntry.Info Property — Gets the object metadata.
• GemEnhancedObjectEntry.Name Property — Gets the object name (OBJSPEC) as an ASCII item.
• GemEnhancedObjectInfo.CommandCount Property — The number of command definitions of the object.
• GemEquipmentOptions.InitialControl Property — Gets the control state the equipment starts in. GemControlState.AttemptOnline is rejected.
• GemEquipmentOptions.ItemLimits Property — Gets the SECS-II limits applied to GEM messages, status values and each GemResult.
• GemEquipmentOptions.MaxMetadataBytes Property — Gets the maximum total bytes of all registered status variable names and units.
• GemEquipmentOptions.MaxValueBytes Property — Gets the maximum total encoded bytes of all registered status variable values.
• GemEquipmentOptions.MaxVariables Property — Gets the maximum number of status variables (SVIDs) that can be registered.
• GemEquipmentOptions.Model Property — Gets the equipment model type (MDLN) reported in S1F2 and S1F13/S1F14. Must contain only ASCII characters.
• GemEquipmentOptions.OnlineMode Property — Gets the on-line state (local or remote) the equipment enters when it goes on-line.
• GemEquipmentOptions.SoftwareRevision Property — Gets the software revision (SOFTREV) reported in S1F2 and S1F13/S1F14. Must contain only ASCII characters.
• GemEquipmentSpoolConfiguration.Catalog Property — The primary messages that can be spooled, in order; empty to accept the catalog of an existing snapshot file.
• GemEquipmentSpoolConfiguration.LocalPolicy Property — The local spooling policy, or null to keep the policy of a new spool (disabled) or of the loaded file.
• GemEquipmentSpoolConfiguration.Options Property — The spool limits.
• GemEquipmentSpoolConfiguration.Path Property — The path of the snapshot file, whose parent directory must exist, or null for an in-memory spool.
• GemEquipmentSpoolConfiguration.Selections Property — The stream selections applied with LocalPolicy; not applied when it is null, but still checked against the limits.
• GemEvent.ProcessingStatus Property — Gets PdcommStatus.Ok when GemEvent.Result is available, or the status that GemEndpoint.HandleEvent failed with, for example PdcommStatus.StaleToken.
• GemEvent.Result Property — Gets the GEM result, or null when processing failed; GemEvent.ProcessingStatus then holds the reason.
• GemEvent.TransportEvent Property — Gets the raw HSMS event, which stays readable after GEM processing.
• GemEventDefinition.Enabled Property — true when reporting of the event is enabled.
• GemEventDefinition.EventId Property — The collection event ID (CEID).
• GemEventDefinition.ReportIds Property — The linked report IDs (RPTIDs) in link order; empty when the event is not linked.
• GemEventDirectoryDefinition.Id Property — The collection event ID (CEID). The directory must list exactly the events registered in the event report store.
• GemEventDirectoryDefinition.Name Property — The ASCII event name (CENAME) reported in S1F24; may be empty.
• GemEventDirectoryDefinition.VariableIds Property — The variable IDs (VIDs) reported for the event in S1F24, without duplicates. Each VID must be bound to an existing data variable (GemDataSourceKind.Data).
• GemEventInfo.Acknowledged Property — true after GemHost.AcknowledgeEvent sent S6F12 for the result.
• GemEventInfo.DataId Property — The data ID (DATAID) of the message.
• GemEventInfo.EventId Property — The collection event ID (CEID).
• GemEventInfo.ReportCount Property — The number of reports in the message.
• GemEventReport.ReportId Property — The report ID (RPTID).
• GemEventReport.ValueCount Property — The number of variable values (V) in the report.
• GemFixedEventDefinition.Enabled Property — Whether the event starts enabled for reporting.
• GemFixedEventDefinition.Id Property — The collection event ID (CEID).
• GemFixedEventDefinition.ReportIds Property — The report IDs (RPTID) linked to the event, in report order.
• GemFormattedProgramCapabilityCommand.AfterDependency Property — The after-dependency value (ACDS); it is sent as a single U2 value.
• GemFormattedProgramCapabilityCommand.BeforeDependencies Property — The before-dependency values (BCDS); they are sent as a U2 array.
• GemFormattedProgramCapabilityCommand.BlockDefinition Property — The block definition (BLKDEF): -1, 0 or 1; it is sent as an I1 item.
• GemFormattedProgramCapabilityCommand.Code Property — The command code (CCODE): ASCII text of at most GemFormattedProgramCapabilityOptions.MaxCommandCodeBytes bytes.
• GemFormattedProgramCapabilityCommand.ImmediateAfterDependencies Property — The immediately-after dependency values (IACDS); they are sent as a U2 array.
• GemFormattedProgramCapabilityCommand.ImmediateBeforeDependencies Property — The immediately-before dependency values (IBCDS); they are sent as a U2 array.
• GemFormattedProgramCapabilityCommand.Name Property — The command name (CNAME): ASCII text of at most 16 bytes.
• GemFormattedProgramCapabilityCommand.NonAfterDependencies Property — The not-after dependency values (NACDS); they are sent as a U2 array.
• GemFormattedProgramCapabilityCommand.NonBeforeDependencies Property — The not-before dependency values (NBCDS); they are sent as a U2 array.
• GemFormattedProgramCapabilityCommand.Parameters Property — The parameter descriptors in wire order: each one is a list item with 4, 5 or 9 elements.
• GemFormattedProgramCapabilityCommand.Required Property — Whether a program must contain the command (RQCMD); it is sent as a Boolean item.
• GemFormattedProgramCapabilityCommandInfo.AfterDependency Property — The single U2 after-dependency value (ACDS).
• GemFormattedProgramCapabilityCommandInfo.BeforeDependencyCount Property — The number of U2 values in the before-dependency list (BCDS).
• GemFormattedProgramCapabilityCommandInfo.BlockDefinition Property — The block definition (BLKDEF): -1, 0 or 1.
• GemFormattedProgramCapabilityCommandInfo.ImmediateAfterDependencyCount Property — The number of U2 values in the immediate-after list (IACDS).
• GemFormattedProgramCapabilityCommandInfo.ImmediateBeforeDependencyCount Property — The number of U2 values in the immediate-before list (IBCDS).
• GemFormattedProgramCapabilityCommandInfo.NonAfterDependencyCount Property — The number of U2 values in the not-after list (NACDS).
• GemFormattedProgramCapabilityCommandInfo.NonBeforeDependencyCount Property — The number of U2 values in the not-before list (NBCDS).
• GemFormattedProgramCapabilityCommandInfo.ParameterCount Property — The number of parameter descriptions; each is a list of 4, 5 or 9 items.
• GemFormattedProgramCapabilityCommandInfo.Required Property — The RQCMD flag: 1 when a process program must contain the command, otherwise 0.
• GemFormattedProgramCapabilityInfo.ByteMaximum Property — The BYTMAX value: the largest encoded size, in bytes, of a process program.
• GemFormattedProgramCapabilityInfo.CommandCount Property — The number of commands in the capability data.
• GemFormattedProgramCapabilityInfo.CommandMaximum Property — The CMDMAX value: the largest number of commands a process program may contain.
• GemFormattedProgramCapabilityInfo.IsRequest Property — Whether the result is a received S7F21 that this equipment answers.
• GemFormattedProgramCapabilityInfo.ReplyReady Property — Whether a received S7F21 still waits for GemFormattedPrograms.RespondCapabilityQuery.
• GemFormattedProgramCapabilityInfo.RequestKind Property — The request kind 39 (GemRequestKind.FormattedCapability).
• GemFormattedProgramCapabilityInfo.Responded Property — Whether the S7F22 was sent by this equipment or received by this host.
• GemFormattedProgramCapabilityOptions.MaxCapabilityBytes Property — The largest encoded size, in bytes, of the whole S7F22 capability data.
• GemFormattedProgramCapabilityOptions.MaxCommandCodeBytes Property — The longest command code (CCODE), in bytes.
• GemFormattedProgramCapabilityOptions.MaxCommands Property — The largest number of commands in the capability data.
• GemFormattedProgramCapabilityOptions.MaxDependenciesPerField Property — The largest number of values in one dependency list of a command (BCDS, IBCDS, NBCDS, IACDS or NACDS).
• GemFormattedProgramCapabilityOptions.MaxHistory Property — The number of completed transaction identities the endpoint remembers to reject a replayed reply or a repeated response; the oldest is forgotten when full. Must be nonzero.
• GemFormattedProgramCapabilityOptions.MaxParametersPerCommand Property — The largest number of parameter descriptions in one command.
• GemFormattedProgramCapabilityOptions.MaxPending Property — The largest number of primaries this endpoint sent that still wait for their reply; a further send fails with PdcommStatus.LimitExceeded. Must be nonzero.
• GemFormattedProgramCapabilityOptions.MaxReceived Property — The largest number of received primaries that wait for this endpoint's response; a further primary is reported as an GemResultKind.Unhandled result. Must be nonzero.
• GemFormattedProgramCapabilityOptions.MaxResults Property — The number of completed transactions the endpoint retains; the oldest is discarded when full. Must be nonzero.
• GemFormattedProgramCapabilityOptions.MaxTotalDependencies Property — The largest number of dependency values across all commands; the single ACDS value of each command counts as one.
• GemFormattedProgramCapabilityOptions.MaxTotalParameterBytes Property — The largest total encoded size, in bytes, of all parameter descriptions.
• GemFormattedProgramCapabilityOptions.MaxTotalParameters Property — The largest number of parameter descriptions across all commands.
• GemFormattedProgramCommand.Code Property — The command code (CCODE): an ASCII item, or a U1, U2, U4 or U8 item that holds exactly one value.
• GemFormattedProgramCommand.Parameters Property — The command parameters (PPARM) in wire order; any item format is accepted.
• GemFormattedProgramCommandInfo.CodeFormat Property — The SECS-II format of the command code (CCODE) item.
• GemFormattedProgramCommandInfo.ParameterCount Property — The number of parameters (PPARM) of the command.
• GemFormattedProgramConfiguration.Capabilities Property — The options for the S7F21/S7F22 process capabilities service, passed to GemFormattedPrograms.ConfigureCapabilities.
• GemFormattedProgramConfiguration.Queries Property — The options for the S7F25/S7F26 formatted program request service and the equipment's local store, selection and execution tracking, passed to GemFormattedPrograms.ConfigureQueries.
• GemFormattedProgramConfiguration.Transfers Property — The options for the S7F23/S7F24 formatted program send service, passed to GemFormattedPrograms.ConfigureTransfers.
• GemFormattedProgramConfiguration.VerificationNegotiation Property — The options for the S7F29/S7F30 verification negotiation, passed to GemFormattedPrograms.ConfigureVerificationNegotiation.
• GemFormattedProgramConfiguration.VerificationReports Property — The options for the S7F27/S7F28 verification report service, passed to GemFormattedPrograms.ConfigureVerificationReports.
• GemFormattedProgramConfiguration.VerificationRequests Property — The options for the S7F31/S7F32 verification request service, passed to GemFormattedPrograms.ConfigureVerificationRequests.
• GemFormattedProgramDryRunInfo.CapabilityPresent Property — Whether the equipment's capability catalog held data; without it the report has an indeterminate capability-missing issue. 1 when set, otherwise 0.
• GemFormattedProgramDryRunInfo.CapabilityRevision Property — The revision of the capability catalog the program was compared with.
• GemFormattedProgramDryRunInfo.CommandCount Property — The number of commands in the evaluated program.
• GemFormattedProgramDryRunInfo.EncodedBytes Property — The encoded size, in bytes, of the evaluated program (its S7F23 body).
• GemFormattedProgramDryRunInfo.EndpointId Property — The process-local identity of the endpoint that produced the report.
• GemFormattedProgramDryRunInfo.EntryGeneration Property — The store entry generation captured when the program was selected.
• GemFormattedProgramDryRunInfo.IdFormat Property — The SECS-II format code of the evaluated program's PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary).
• GemFormattedProgramDryRunInfo.IssueCount Property — The number of issues; read each with GemFormattedProgramDryRunReport.GetIssueInfo.
• GemFormattedProgramDryRunInfo.Outcome Property — The overall outcome, the most severe outcome of all issues: 0 pass, 1 indeterminate or 2 reject; see GemFormattedProgramDryRunOutcome.
• GemFormattedProgramDryRunInfo.PolicyVersion Property — The policy version the report was evaluated with.
• GemFormattedProgramDryRunInfo.SelectionGeneration Property — The selection generation of the evaluated selection.
• GemFormattedProgramDryRunInfo.SessionGeneration Property — The connection generation in which the evaluated program was selected.
• GemFormattedProgramDryRunInfo.StoreRevision Property — The program store revision captured when the program was selected.
• GemFormattedProgramDryRunIssueInfo.Code Property — The issue code: 1 capability missing, 2 model mismatch, 3 software revision mismatch, 4 command count exceeded, 5 encoded bytes exceeded, 6 unknown ASCII command, 7 required command missing, 8 unsigned command code unmapped, 9 dependency semantics not evaluated, 10 program parameter semantics not evaluated, 11 capability parameter semantics not evaluated.
• GemFormattedProgramDryRunIssueInfo.CommandIndex Property — The zero-based command index: a command of the program for codes 6, 8 and 10, a command of the capability catalog for codes 7, 9 and 11.
• GemFormattedProgramDryRunIssueInfo.Expected Property — The expected maximum: CMDMAX for code 4 and BYTMAX for code 5.
• GemFormattedProgramDryRunIssueInfo.FieldIndex Property — The zero-based field index; policy version 1 never sets it.
• GemFormattedProgramDryRunIssueInfo.Observed Property — The observed value: the program's command count for code 4, its encoded size in bytes for code 5, and the command's parameter count for codes 10 and 11.
• GemFormattedProgramDryRunIssueInfo.Outcome Property — The outcome the issue contributes: 1 indeterminate or 2 reject; see GemFormattedProgramDryRunOutcome.
• GemFormattedProgramDryRunIssueInfo.PresenceMask Property — Bit flags of the optional fields: 1 GemFormattedProgramDryRunIssueInfo.CommandIndex, 2 GemFormattedProgramDryRunIssueInfo.FieldIndex, 4 GemFormattedProgramDryRunIssueInfo.Observed, 8 GemFormattedProgramDryRunIssueInfo.Expected.
• GemFormattedProgramDryRunOptions.MaxIssues Property — The largest number of issues the report may hold.
• GemFormattedProgramDryRunOptions.MaxProgramEncodedBytes Property — The largest encoded size, in bytes, of the selected process program (its S7F23 body) that the dry run evaluates.
• GemFormattedProgramDryRunOptions.PolicyVersion Property — The evaluation policy version. Only 1 is supported; other values fail with PdcommStatus.InvalidArgument.
• GemFormattedProgramExecutionActionInfo.ActionSequence Property — The sequence number of the action within its execution; the start action is 1.
• GemFormattedProgramExecutionActionInfo.CancelNextCommandIndex Property — For a cancel action, the zero-based index of the next command that had not been applied when the cancellation was requested.
• GemFormattedProgramExecutionActionInfo.CapabilityRevision Property — For a start action, the capability catalog revision of the dry run.
• GemFormattedProgramExecutionActionInfo.CodeFormat Property — For a step action, the SECS-II format code of the command code (CCODE): 16 ASCII, or 41, 42, 44 or 40 for U1, U2, U4 or U8; see SecsFormat.
• GemFormattedProgramExecutionActionInfo.CommandCount Property — The number of commands in the executed program.
• GemFormattedProgramExecutionActionInfo.CommandIndex Property — For a step action, the zero-based index of the command to perform.
• GemFormattedProgramExecutionActionInfo.DryRunOutcome Property — For a start action, the GemFormattedProgramDryRunOutcome code of the dry run that admitted the execution.
• GemFormattedProgramExecutionActionInfo.EndpointId Property — The process-local identity of the endpoint that runs the execution.
• GemFormattedProgramExecutionActionInfo.ExecutionGeneration Property — The execution number of the execution the action belongs to.
• GemFormattedProgramExecutionActionInfo.IdFormat Property — For a start action, the SECS-II format code of the program's PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary).
• GemFormattedProgramExecutionActionInfo.Kind Property — The action kind: 1 start, 2 step or 3 cancel.
• GemFormattedProgramExecutionActionInfo.ParameterCount Property — For a step action, the number of parameters of the command.
• GemFormattedProgramExecutionActionInfo.PolicyVersion Property — For a start action, the dry run policy version.
• GemFormattedProgramExecutionActionInfo.PresenceMask Property — Bit flags: 1 program ID, 2 model and 4 software revision for a start action, 8 command for a step action, 16 GemFormattedProgramExecutionActionInfo.CancelNextCommandIndex for a cancel action.
• GemFormattedProgramExecutionActionInfo.SessionGeneration Property — The connection generation in which the execution started.
• GemFormattedProgramExecutionActionToken.ActionSequence Property — The sequence number of the action within its execution; the start action is 1.
• GemFormattedProgramExecutionActionToken.EndpointId Property — The process-local identity of the endpoint that runs the execution.
• GemFormattedProgramExecutionActionToken.ExecutionGeneration Property — The execution number of the execution the action belongs to.
• GemFormattedProgramExecutionActionToken.Kind Property — The action kind: 1 start, 2 step or 3 cancel.
• GemFormattedProgramExecutionActionToken.SessionGeneration Property — The connection generation in which the execution started.
• GemFormattedProgramExecutionInfo.ApplicationDetailLength Property — The length, in bytes, of the detail of the application report; read it with GemFormattedProgramExecutionSnapshot.GetApplicationDetailBytes.
• GemFormattedProgramExecutionInfo.ApplicationReportId Property — The report ID that the application passed with its terminal report.
• GemFormattedProgramExecutionInfo.ApplicationReportKind Property — The GemFormattedProgramTerminalOutcome code of the application report, or 0 when there is none.
• GemFormattedProgramExecutionInfo.CapabilityPresent Property — Whether the starting dry run had capability data; 1 when set, otherwise 0.
• GemFormattedProgramExecutionInfo.CapabilityRevision Property — The capability catalog revision of the starting dry run.
• GemFormattedProgramExecutionInfo.CommandCount Property — The number of commands in the executed program.
• GemFormattedProgramExecutionInfo.DryRunOutcome Property — The GemFormattedProgramDryRunOutcome code of the dry run the execution started from.
• GemFormattedProgramExecutionInfo.EndpointId Property — The process-local identity of the endpoint that runs the execution.
• GemFormattedProgramExecutionInfo.EntryGeneration Property — The store entry generation captured when the executed program was selected.
• GemFormattedProgramExecutionInfo.ExecutionGeneration Property — The execution number.
• GemFormattedProgramExecutionInfo.IdFormat Property — The SECS-II format code of the executed program's PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary).
• GemFormattedProgramExecutionInfo.NextCommandIndex Property — The zero-based index of the next command to step; it advances when a step action is reported as applied.
• GemFormattedProgramExecutionInfo.PendingActionSequence Property — The sequence number of the pending action.
• GemFormattedProgramExecutionInfo.PendingKind Property — The kind of the pending action: 0 none, 1 start, 2 step or 3 cancel.
• GemFormattedProgramExecutionInfo.PolicyVersion Property — The dry run policy version the execution started from.
• GemFormattedProgramExecutionInfo.PresenceMask Property — Bit flags: 1 an action is pending, 2 the application reported a terminal outcome with GemFormattedPrograms.CompleteExecution, 4 that report has detail bytes.
• GemFormattedProgramExecutionInfo.SelectionGeneration Property — The selection generation of the selection the execution started from.
• GemFormattedProgramExecutionInfo.SessionGeneration Property — The connection generation in which the execution started.
• GemFormattedProgramExecutionInfo.State Property — The GemFormattedProgramExecutionState code, 0 empty to 9 outcome unknown; the states from 5 on are terminal.
• GemFormattedProgramExecutionInfo.StoreRevision Property — The program store revision captured when the executed program was selected.
• GemFormattedProgramExecutionStart.Action Property — The start action, which owns native memory. Disposing this object disposes it.
• GemFormattedProgramExecutionStart.Token Property — The token that identifies the execution; pass it to GemFormattedPrograms.StepExecution, GemFormattedPrograms.CancelExecution and GemFormattedPrograms.CompleteExecution.
• GemFormattedProgramExecutionToken.EndpointId Property — The process-local identity of the endpoint that started the execution.
• GemFormattedProgramExecutionToken.ExecutionGeneration Property — The execution number; each start of a new execution increases it by one.
• GemFormattedProgramExecutionToken.SessionGeneration Property — The connection generation in which the execution started.
• GemFormattedProgramInfo.IdFormat Property — The SECS-II format code of the received PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary). 0 on an acknowledgement result.
• GemFormattedProgramInfo.IsRequest Property — Whether the result is a received S7F27 that this host answers.
• GemFormattedProgramInfo.IssueCount Property — The number of issues in the received report; 0 on an acknowledgement result.
• GemFormattedProgramInfo.ReplyReady Property — Whether a received S7F27 still waits for GemFormattedPrograms.RespondVerificationReport.
• GemFormattedProgramInfo.RequestKind Property — The request kind 35 (GemRequestKind.FormattedVerificationReport).
• GemFormattedProgramInfo.Responded Property — Whether the S7F28 was sent by this host or received by this equipment.
• GemFormattedProgramIssue.Code Property — The verification result code, from 0 through 5; it is sent as a U4 item.
• GemFormattedProgramIssue.Sequence Property — The sequence number (SEQNUM) that the issue refers to; it is sent as a U4 item.
• GemFormattedProgramIssue.Text Property — The error text (ERRW7): ASCII and possibly empty. A code of 0 with empty text is still an issue, distinct from an empty issue list.
• GemFormattedProgramOptions.MaxHistory Property — The number of completed transaction identities the endpoint remembers to reject a replayed reply or a repeated response; the oldest is forgotten when full. Must be nonzero.
• GemFormattedProgramOptions.MaxIssueTextBytes Property — The longest issue text (ERRW7), in bytes.
• GemFormattedProgramOptions.MaxIssues Property — The largest number of issues in one S7F27 report, sent or received.
• GemFormattedProgramOptions.MaxPending Property — The largest number of primaries this endpoint sent that still wait for their reply; a further send fails with PdcommStatus.LimitExceeded. Must be nonzero.
• GemFormattedProgramOptions.MaxReceived Property — The largest number of received primaries that wait for this endpoint's response; a further primary is reported as an GemResultKind.Unhandled result. Must be nonzero.
• GemFormattedProgramOptions.MaxResults Property — The number of completed transactions the endpoint retains; the oldest is discarded when full. Must be nonzero.
• GemFormattedProgramOptions.MaxTotalIssueTextBytes Property — The largest total length, in bytes, of all issue texts of one report.
• GemFormattedProgramPayload.Commands Property — The program commands in execution order.
• GemFormattedProgramPayload.Id Property — The process program ID (PPID): a nonempty ASCII or Binary item of at most 120 bytes.
• GemFormattedProgramPayload.Model Property — The equipment model type (MDLN): ASCII text of at most 20 bytes, possibly empty.
• GemFormattedProgramPayload.SoftwareRevision Property — The software revision (SOFTREV): ASCII text of at most 20 bytes, possibly empty.
• GemFormattedProgramQueryInfo.CommandCount Property — The number of commands in the returned program; 0 when no program is present.
• GemFormattedProgramQueryInfo.IdFormat Property — The SECS-II format code of the requested PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary).
• GemFormattedProgramQueryInfo.IsRequest Property — Whether the result is a received S7F25 that this equipment answers.
• GemFormattedProgramQueryInfo.Present Property — Whether the S7F26 data carries the requested process program.
• GemFormattedProgramQueryInfo.PresentKnown Property — Whether the answer is known, so that GemFormattedProgramQueryInfo.Present is meaningful; a received S7F25 that is not answered yet has 0.
• GemFormattedProgramQueryInfo.ReplyReady Property — Whether a received S7F25 still waits for GemFormattedPrograms.RespondQuery.
• GemFormattedProgramQueryInfo.RequestKind Property — The request kind 37 (GemRequestKind.FormattedQuery).
• GemFormattedProgramQueryInfo.Responded Property — Whether the S7F26 was sent by this equipment or received by this host.
• GemFormattedProgramQueryOptions.MaxCatalogEntries Property — The largest number of process programs the equipment's store holds.
• GemFormattedProgramQueryOptions.MaxCatalogIdentifierBytes Property — The largest total length, in bytes, of the PPIDs of all stored programs.
• GemFormattedProgramQueryOptions.MaxCommands Property — The largest number of commands in one process program that is stored or received in S7F26.
• GemFormattedProgramQueryOptions.MaxHistory Property — The number of completed transaction identities the endpoint remembers to reject a replayed reply or a repeated response; the oldest is forgotten when full. Must be nonzero.
• GemFormattedProgramQueryOptions.MaxParametersPerCommand Property — The largest number of parameters (PPARM) in one command.
• GemFormattedProgramQueryOptions.MaxPending Property — The largest number of primaries this endpoint sent that still wait for their reply; a further send fails with PdcommStatus.LimitExceeded. Must be nonzero.
• GemFormattedProgramQueryOptions.MaxReceived Property — The largest number of received primaries that wait for this endpoint's response; a further primary is reported as an GemResultKind.Unhandled result. Must be nonzero.
• GemFormattedProgramQueryOptions.MaxResults Property — The number of completed transactions the endpoint retains; the oldest is discarded when full. Must be nonzero.
• GemFormattedProgramQueryOptions.MaxTotalParameterBytes Property — The largest total encoded size, in bytes, of all parameters of one process program.
• GemFormattedProgramQueryOptions.MaxTotalParameters Property — The largest number of parameters across all commands of one process program.
• GemFormattedProgramSelectionInfo.CommandCount Property — The number of commands in the selected program.
• GemFormattedProgramSelectionInfo.EntryGeneration Property — The generation of the selected store entry when the program was selected.
• GemFormattedProgramSelectionInfo.IdFormat Property — The SECS-II format code of the selected PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary).
• GemFormattedProgramSelectionInfo.SelectionGeneration Property — The current selection generation.
• GemFormattedProgramSelectionInfo.SessionGeneration Property — The connection generation in which the program was selected.
• GemFormattedProgramSelectionInfo.StaleReason Property — Why a stale selection is stale: 1 the store entry was deleted, 2 the entry changed, 3 the connection generation changed, 4 the connection was lost; 0 when the selection is not stale.
• GemFormattedProgramSelectionInfo.State Property — The selection state: 0 empty, 1 ready or 2 stale.
• GemFormattedProgramSelectionInfo.StoreRevision Property — The program store revision when the program was selected.
• GemFormattedProgramSelectionInfo.ValidForExecution Property — Whether the selection is ready and can start an execution; 1 when set, otherwise 0.
• GemFormattedProgramSelectionToken.EndpointId Property — The process-local identity of the endpoint that made the selection.
• GemFormattedProgramSelectionToken.EntryGeneration Property — The generation of the selected store entry when the program was selected.
• GemFormattedProgramSelectionToken.SelectionGeneration Property — The selection generation; it increases when a new selection replaces the current one and when the selection is cleared.
• GemFormattedProgramSelectionToken.SessionGeneration Property — The connection generation in which the program was selected.
• GemFormattedProgramSelectionToken.StoreRevision Property — The program store revision when the program was selected.
• GemFormattedProgramStoreEntryInfo.CommandCount Property — The number of commands in the program.
• GemFormattedProgramStoreEntryInfo.IdFormat Property — The SECS-II format code of the program's PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary).
• GemFormattedProgramStoreInfo.EncodedBytes Property — The total encoded size, in bytes, of the stored programs, each counted as its S7F23 body.
• GemFormattedProgramStoreInfo.EntryCount Property — The number of stored process programs.
• GemFormattedProgramStoreInfo.IdentifierBytes Property — The total length, in bytes, of the PPIDs of the stored programs.
• GemFormattedProgramStoreInfo.MaxEncodedBytes Property — The largest total encoded size, in bytes: GemFormattedProgramStoreInfo.MaxEntries times SecsLimits.MessageBytes of the equipment's item limits.
• GemFormattedProgramStoreInfo.MaxEntries Property — The largest number of stored programs, GemFormattedProgramQueryOptions.MaxCatalogEntries.
• GemFormattedProgramStoreInfo.MaxIdentifierBytes Property — The largest total PPID length, in bytes, GemFormattedProgramQueryOptions.MaxCatalogIdentifierBytes.
• GemFormattedProgramStoreInfo.Revision Property — The store revision; it increases when the stored programs change.
• GemFormattedProgramTransferInfo.Acknowledgement Property — The ACKC7 code (0 to 7) that was received or sent; meaningful when GemFormattedProgramTransferInfo.AcknowledgementPresent is 1.
• GemFormattedProgramTransferInfo.AcknowledgementPresent Property — Whether GemFormattedProgramTransferInfo.Acknowledgement holds a received or sent ACKC7 code.
• GemFormattedProgramTransferInfo.CommandCount Property — The number of commands in the received program; 0 on an acknowledgement result.
• GemFormattedProgramTransferInfo.IdFormat Property — The SECS-II format code of the received PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary). 0 on an acknowledgement result.
• GemFormattedProgramTransferInfo.IsRequest Property — Whether the result is a received S7F23 that this equipment answers.
• GemFormattedProgramTransferInfo.ReplyReady Property — Whether a received S7F23 still waits for GemFormattedPrograms.RespondTransfer or GemFormattedPrograms.RespondTransferAndStore.
• GemFormattedProgramTransferInfo.RequestKind Property — The request kind 36 (GemRequestKind.FormattedTransfer).
• GemFormattedProgramTransferInfo.Responded Property — Whether the S7F24 was sent by this equipment or received by this host.
• GemFormattedProgramTransferOptions.MaxCommands Property — The largest number of commands in one process program that is sent or received in S7F23.
• GemFormattedProgramTransferOptions.MaxHistory Property — The number of completed transaction identities the endpoint remembers to reject a replayed reply or a repeated response; the oldest is forgotten when full. Must be nonzero.
• GemFormattedProgramTransferOptions.MaxParametersPerCommand Property — The largest number of parameters (PPARM) in one command.
• GemFormattedProgramTransferOptions.MaxPending Property — The largest number of primaries this endpoint sent that still wait for their reply; a further send fails with PdcommStatus.LimitExceeded. Must be nonzero.
• GemFormattedProgramTransferOptions.MaxReceived Property — The largest number of received primaries that wait for this endpoint's response; a further primary is reported as an GemResultKind.Unhandled result. Must be nonzero.
• GemFormattedProgramTransferOptions.MaxResults Property — The number of completed transactions the endpoint retains; the oldest is discarded when full. Must be nonzero.
• GemFormattedProgramTransferOptions.MaxTotalParameterBytes Property — The largest total encoded size, in bytes, of all parameters of one process program.
• GemFormattedProgramTransferOptions.MaxTotalParameters Property — The largest number of parameters across all commands of one process program.
• GemFormattedProgramVerificationNegotiationInfo.Correlation Property — The sequence number of the negotiation within its connection generation; every result of one negotiation carries the same value.
• GemFormattedProgramVerificationNegotiationInfo.Length Property — The LENGTH value of the S7F29: the encoded size, in bytes, of the S7F27 report body.
• GemFormattedProgramVerificationNegotiationInfo.NegotiationTerminal Property — How the inquire ended: 0 not yet or ended by a malformed S7F30, 1 granted, 2 denied, 3 timed out, 4 disconnected.
• GemFormattedProgramVerificationNegotiationInfo.PpGnt Property — The PPGNT code (0 to 63, where 0 grants); meaningful when GemFormattedProgramVerificationNegotiationInfo.PpGntPresent is 1.
• GemFormattedProgramVerificationNegotiationInfo.PpGntPresent Property — Whether GemFormattedProgramVerificationNegotiationInfo.PpGnt holds a received or sent grant code.
• GemFormattedProgramVerificationNegotiationInfo.Prepared Property — Whether the result describes this equipment's own negotiation rather than a received S7F29.
• GemFormattedProgramVerificationNegotiationInfo.ReplyReady Property — Whether a received S7F29 still waits for GemFormattedPrograms.RespondVerification.
• GemFormattedProgramVerificationNegotiationInfo.RequestKind Property — The request kind: 40 (GemRequestKind.FormattedVerificationNegotiation) for the inquire and grant, or 35 (GemRequestKind.FormattedVerificationReport) for the S7F28 acknowledgement of the S7F27 sent after the grant.
• GemFormattedProgramVerificationNegotiationInfo.Responded Property — Whether this host sent its S7F30 answer.
• GemFormattedProgramVerificationNegotiationInfo.State Property — The negotiation state: 1 prepared by this equipment, 2 received by this host, 3 answered by this host.
• GemFormattedProgramVerificationNegotiationInfo.Submitted Property — Whether the equipment sent the S7F29 inquire.
• GemFormattedProgramVerificationNegotiationInfo.VerificationTerminal Property — How the S7F27 send after a grant ended: 0 not yet or ended by a malformed S7F28, 1 acknowledged with S7F28, 3 timed out, 4 disconnected.
• GemFormattedProgramVerificationNegotiationOptions.MaxHistory Property — The number of completed transaction identities the endpoint remembers to reject a replayed reply or a repeated response; the oldest is forgotten when full. Must be nonzero.
• GemFormattedProgramVerificationNegotiationOptions.MaxIssueTextBytes Property — The longest issue text (ERRW7), in bytes.
• GemFormattedProgramVerificationNegotiationOptions.MaxIssues Property — The largest number of issues in the S7F27 report of one prepared negotiation.
• GemFormattedProgramVerificationNegotiationOptions.MaxPending Property — The largest number of submitted negotiations that wait for their S7F30 grant or S7F28 acknowledgement; a further submit fails with PdcommStatus.LimitExceeded. Must be nonzero.
• GemFormattedProgramVerificationNegotiationOptions.MaxPrepared Property — The largest number of negotiations the equipment holds after GemFormattedPrograms.PrepareVerification until they end by acknowledgement, denial, timeout, disconnection or a malformed reply; a further prepare fails with PdcommStatus.LimitExceeded. Must be nonzero.
• GemFormattedProgramVerificationNegotiationOptions.MaxReceived Property — The largest number of received primaries that wait for this endpoint's response; a further primary is reported as an GemResultKind.Unhandled result. Must be nonzero.
• GemFormattedProgramVerificationNegotiationOptions.MaxResults Property — The number of completed negotiations the endpoint retains; the oldest is discarded when full. Must be nonzero.
• GemFormattedProgramVerificationNegotiationOptions.MaxTotalIssueTextBytes Property — The largest total length, in bytes, of all issue texts of one report.
• GemFormattedProgramVerificationRequestInfo.Acknowledgement Property — The ACKC7 code (0 to 7) that was received or sent; meaningful when GemFormattedProgramVerificationRequestInfo.AcknowledgementPresent is 1.
• GemFormattedProgramVerificationRequestInfo.AcknowledgementPresent Property — Whether GemFormattedProgramVerificationRequestInfo.Acknowledgement holds a received or sent ACKC7 code.
• GemFormattedProgramVerificationRequestInfo.CommandCount Property — The number of commands in the received program; 0 on an acknowledgement result.
• GemFormattedProgramVerificationRequestInfo.IdFormat Property — The SECS-II format code of the received PPID: 16 (SecsFormat.Ascii) or 8 (SecsFormat.Binary). 0 on an acknowledgement result.
• GemFormattedProgramVerificationRequestInfo.IsRequest Property — Whether the result is a received S7F31 that this equipment answers.
• GemFormattedProgramVerificationRequestInfo.ReplyReady Property — Whether a received S7F31 still waits for GemFormattedPrograms.RespondVerificationRequest.
• GemFormattedProgramVerificationRequestInfo.RequestKind Property — The request kind 38 (GemRequestKind.FormattedVerificationRequest).
• GemFormattedProgramVerificationRequestInfo.Responded Property — Whether the S7F32 was sent by this equipment or received by this host.
• GemFormattedProgramVerificationRequestOptions.MaxCommands Property — The largest number of commands in one process program that is sent or received in S7F31.
• GemFormattedProgramVerificationRequestOptions.MaxHistory Property — The number of completed transaction identities the endpoint remembers to reject a replayed reply or a repeated response; the oldest is forgotten when full. Must be nonzero.
• GemFormattedProgramVerificationRequestOptions.MaxParametersPerCommand Property — The largest number of parameters (PPARM) in one command.
• GemFormattedProgramVerificationRequestOptions.MaxPending Property — The largest number of primaries this endpoint sent that still wait for their reply; a further send fails with PdcommStatus.LimitExceeded. Must be nonzero.
• GemFormattedProgramVerificationRequestOptions.MaxReceived Property — The largest number of received primaries that wait for this endpoint's response; a further primary is reported as an GemResultKind.Unhandled result. Must be nonzero.
• GemFormattedProgramVerificationRequestOptions.MaxResults Property — The number of completed transactions the endpoint retains; the oldest is discarded when full. Must be nonzero.
• GemFormattedProgramVerificationRequestOptions.MaxTotalParameterBytes Property — The largest total encoded size, in bytes, of all parameters of one process program.
• GemFormattedProgramVerificationRequestOptions.MaxTotalParameters Property — The largest number of parameters across all commands of one process program.
• GemHostOptions.ItemLimits Property — Gets the SECS-II limits applied to GEM messages and to the data kept in each GemResult.
• GemHostOptions.MaxPendingIds Property — Gets the maximum number of requested IDs that pending host requests can hold at once.
• GemLinkSpec.EventId Property — The collection event ID (CEID).
• GemLinkSpec.ReportIds Property — The report IDs (RPTIDs) to link to the event. An empty list asks the equipment to unlink all reports from the event.
• GemProgramConfiguration.InitialPrograms Property — The programs to store in order with GemEquipment.PutProgram after the store is opened. With a storage file that already holds a PPID, GemProgramPutMode.Create fails and stops the startup.
• GemProgramConfiguration.Options Property — The store limits and grant policy.
• GemProgramConfiguration.Path Property — The storage file path, or null or empty to keep the store in memory; see GemEquipment.ConfigurePrograms.
• GemProgramDefinition.Body Property — The process program body (PPBODY): an ASCII, binary, I1 to I8 or U1 to U8 item, which may be empty. Its format and raw bytes are preserved.
• GemProgramDefinition.Id Property — The process program ID (PPID): a nonempty ASCII or binary item of at most GemProgramOptions.MaxIdentifierBytes and 120 bytes. The format is part of the identity.
• GemProgramDefinition.Mode Property — How the program is stored when its PPID already exists.
• GemProgramEntry.Body Property — Gets the process program body (PPBODY).
• GemProgramEntry.Id Property — Gets the process program ID (PPID).
• GemProgramInfo.Acknowledgement Property — PPGNT for S7F1/S7F2 or ACKC7 for S7F3/S7F4 and S7F17/S7F18: the code received in a reply, or the code prepared for a received request; null when there is none.
• GemProgramInfo.Applied Property — Whether a received S7F3 or S7F17 request changed the local store.
• GemProgramInfo.ConfirmationRequired Property — Whether the installation is unconfirmed and the reply is held until GemEquipment.ConfirmProgramReply accepts the uncertainty.
• GemProgramInfo.DeclaredLength Property — The body length (LENGTH) declared by a received S7F1 request; otherwise 0.
• GemProgramInfo.Durability Property — How durably a received S7F3 or S7F17 request was installed by GemEquipment.RespondProgram; GemProgramDurability.None for replies and before a change is installed.
• GemProgramInfo.GrantActivated Property — Whether the reply to a received S7F1 activated a grant. It reports the original activation, not whether the grant is still outstanding.
• GemProgramInfo.IdCount Property — The number of PPIDs: 1 for S7F1, S7F3 and S7F5 requests, the selection size of an S7F17 request (0 means all), 0 for S7F19; 1 for an S7F6 reply with a program and 0 for an unknown program; the directory length of an S7F20 reply; 0 for acknowledgement replies.
• GemProgramInfo.IsRequest Property — true for a received primary; false for a reply.
• GemProgramInfo.PersistenceStatus Property — The numeric PdcommStatus of the persistence failure that left the installation unconfirmed; otherwise 0.
• GemProgramInfo.ReplyReady Property — Whether a prepared reply is waiting to be sent; call GemEquipment.RespondProgram again with the same mode and decision to send it without writing again.
• GemProgramInfo.RequestKind Property — The transaction, from GemRequestKind.ProgramGrant to GemRequestKind.ProgramDirectory.
• GemProgramInfo.Responded Property — Whether the reply to a received primary was sent.
• GemProgramOptions.GrantPolicy Property — Gets whether a received S7F3 needs an earlier S7F1 grant.
• GemProgramOptions.MaxBodyBytes Property — Gets the maximum payload length in bytes of one process program body (PPBODY).
• GemProgramOptions.MaxGrants Property — Gets the maximum number of S7F1 grants that can be outstanding at once; further S7F1 requests are answered with PPGNT 4 (busy).
• GemProgramOptions.MaxIdentifierBytes Property — Gets the maximum length in bytes of one PPID; the effective limit is never more than 120 bytes.
• GemProgramOptions.MaxPendingIdentifierBytes Property — Gets the maximum total PPID bytes that pending outgoing program requests can hold at once.
• GemProgramOptions.MaxPendingIds Property — Gets the maximum number of PPIDs that pending outgoing S7F1, S7F3, S7F5 and S7F17 requests can hold at once.
• GemProgramOptions.MaxPrograms Property — Gets the maximum number of process programs in the store.
• GemProgramOptions.MaxRequestIds Property — Gets the maximum number of PPIDs in one delete selection: a local delete or an S7F17 request.
• GemProgramOptions.MaxReservedBodyBytes Property — Gets the maximum total body length (LENGTH) that outstanding grants can reserve; a request beyond it is answered with PPGNT 4 (busy).
• GemProgramOptions.MaxSerializedBytes Property — Gets the maximum size in bytes of the storage file; used only when the store has a storage path.
• GemProgramOptions.MaxTotalBodyBytes Property — Gets the maximum total payload bytes of all process program bodies in the store.
• GemProgramOptions.MaxTotalIdentifierBytes Property — Gets the maximum total bytes of all PPIDs in the store.
• GemProgramState.BodyBytes Property — The total payload bytes of all stored bodies.
• GemProgramState.GrantCount Property — The number of outstanding S7F1 grants.
• GemProgramState.IdentifierBytes Property — The total bytes of all stored PPIDs.
• GemProgramState.Persistent Property — Whether the store is backed by a storage file.
• GemProgramState.ProgramCount Property — The number of stored programs.
• GemProgramState.ReservedBodyBytes Property — The total body length reserved by outstanding grants.
• GemProgramWriteInfo.Applied Property — Whether the create, replace or delete was installed in the store.
• GemProgramWriteInfo.Durability Property — How durably the change was installed: GemProgramDurability.Volatile, GemProgramDurability.Synced or GemProgramDurability.Unconfirmed.
• GemProgramWriteInfo.PersistenceStatus Property — The numeric PdcommStatus of the persistence failure when Durability is GemProgramDurability.Unconfirmed; otherwise 0.
• GemQueryInfo.DataId Property — The data ID (DATAID) of an S6F16 reply; zero otherwise.
• GemQueryInfo.DataIdPresent Property — true when DataId came from an S6F16 reply.
• GemQueryInfo.Id Property — The requested ID: the CEID for GemReportQueryKind.Event, otherwise the RPTID.
• GemQueryInfo.IsRequest Property — true when the result is a query request received by equipment.
• GemQueryInfo.Kind Property — The query transaction.
• GemQueryInfo.ReportCount Property — The number of reports in an S6F16 reply; zero otherwise.
• GemQueryInfo.Responded Property — true when the received request has been answered successfully.
• GemQueryInfo.ValueCount Property — The number of values: the total across all reports for S6F16, the value count for S6F20 and S6F22, and zero for a received request.
• GemQueryReportInfo.Id Property — The report ID (RPTID).
• GemQueryReportInfo.ValueCount Property — The number of values in the report.
• GemQueryValue.Value Property — Gets the variable value (V).
• GemQueryValue.VariableId Property — Gets the variable ID (VID) of an S6F22 annotated value, or null for S6F16 and S6F20 values, which carry no VID.
• GemReportBinding.ConstantId Property — For GemDataSourceKind.Constant, the equipment constant ID (ECID) as an ASCII item or a single-element integer item; otherwise null. The configuring call copies the item; the caller keeps ownership.
• GemReportBinding.SourceId Property — The status variable ID or data variable ID; must be 0 for GemDataSourceKind.Constant.
• GemReportBinding.SourceKind Property — The kind of value source.
• GemReportBinding.Vid Property — The variable ID (VID) used in report definitions.
• GemReportBindingEntry.ConstantId Property — Gets a copy of the equipment constant ID for GemDataSourceKind.Constant, or null for other sources. Integer IDs can come back as I8 or U8 items. The entry owns the item.
• GemReportBindingEntry.SourceId Property — Gets the status variable ID or data variable ID; 0 for GemDataSourceKind.Constant.
• GemReportBindingEntry.SourceKind Property — Gets the kind of value source.
• GemReportBindingEntry.Vid Property — Gets the variable ID (VID).
• GemReportConfiguration.EventIds Property — The collection event IDs (CEIDs) to register. The worker copies them when it is started.
• GemReportConfiguration.Options Property — The capacity limits of the report store.
• GemReportDefinition.Id Property — The report ID (RPTID).
• GemReportDefinition.VariableIds Property — The variable IDs (VIDs) of the report in report order.
• GemReportOptions.MaxEvents Property — Gets the maximum number of collection events (CEIDs) that the store can register.
• GemReportOptions.MaxReports Property — Gets the maximum number of defined reports (RPTIDs).
• GemReportOptions.MaxReportsPerEvent Property — Gets the maximum number of reports linked to one collection event.
• GemReportOptions.MaxTotalLinks Property — Gets the maximum number of event-to-report links across all collection events.
• GemReportOptions.MaxTotalVariables Property — Gets the maximum number of variable IDs across all defined reports.
• GemReportOptions.MaxVariablesPerReport Property — Gets the maximum number of variable IDs (VIDs) in one report.
• GemReportSpec.Id Property — The report ID (RPTID).
• GemReportSpec.VariableIds Property — The variable IDs (VIDs) of the report in report order. An empty list asks the equipment to delete the report.
• GemReportState.EventCount Property — The number of registered collection events.
• GemReportState.ReportCount Property — The number of defined reports.
• GemReportState.TotalLinks Property — The number of event-to-report links across all collection events.
• GemReportState.TotalVariables Property — The number of variable IDs across all defined reports.
• GemResultInfo.Acknowledgement Property — The SEMI acknowledgement code carried or sent with the message (for example COMMACK, ONLACK or ACKC5), or null when the outcome has none.
• GemResultInfo.Code Property — The failure detail: an HsmsFailureReason value or GemError.Aborted for GemResultKind.Failed, a GemError value for GemResultKind.InvalidResponse and GemResultKind.Unhandled, and zero otherwise.
• GemResultInfo.EntryCount Property — The number of entries in the result, such as status values or names, report query reports or values, alarms, command parameters or program IDs; zero when the result has no entries.
• GemResultInfo.Kind Property — How the transport event was processed.
• GemResultInfo.Outcome Property — What GEM processing concluded.
• GemResultInfo.ReplySent Property — true when GEM processing sent a reply to the received primary.
• GemResultInfo.RequestKind Property — The GEM transaction the result belongs to; zero when the result is not tied to a known transaction.
• GemResultInfo.State Property — The GEM state of the endpoint after the event was processed.
• GemResultInfo.Token Property — The HSMS token of the request or of the received primary.
• GemSpoolEntry.Body Property — Gets a copy of the message body, or null for a header-only message.
• GemSpoolEntry.Info Property — Gets the entry header.
• GemSpoolEntryInfo.BodyPresent Property — true when the message has a body; false for a header-only message.
• GemSpoolEntryInfo.EntryId Property — The entry ID, unique within the spool.
• GemSpoolEntryInfo.Function Property — The function of the stored primary message.
• GemSpoolEntryInfo.ReplyExpected Property — true when the message is delivered with the W-bit set.
• GemSpoolEntryInfo.Stream Property — The stream of the stored primary message.
• GemSpoolHostOptions.MaxFunctionsPerStream Property — Gets the maximum number of functions for one stream in a request or reply.
• GemSpoolHostOptions.MaxPendingItems Property — Gets the maximum number of streams plus functions in one S2F43 request, which also bounds the total number of functions in a received S2F44 or S2F60.
• GemSpoolHostOptions.MaxStreams Property — Gets the maximum number of streams in an S2F43 request and in a received S2F44 or S2F60.
• GemSpoolInfo.Acknowledgement Property — The acknowledgement code: RSPACK of a received S2F44, RSDA of a received S6F24, ACKC5 or ACKC6 of the reply to a delivered S5F1 or S6F11, or the code of the reply that the equipment prepared; null when there is none.
• GemSpoolInfo.Applied Property — true when the last operation on this result installed a spool change.
• GemSpoolInfo.Command Property — The RSDC of the S6F23 request for GemRequestKind.SpoolControl; GemSpoolCommand.Transmit (0) for other kinds.
• GemSpoolInfo.ConfirmationRequired Property — true when the request was applied with unconfirmed persistence and its reply is held until GemEquipment.ConfirmSpoolReply.
• GemSpoolInfo.DeliveryAttempt Property — The attempt number of the delivery for a delivery result; otherwise 0.
• GemSpoolInfo.DeliveryCompleted Property — true when GemEquipment.CompleteSpoolDelivery accepted this delivery result.
• GemSpoolInfo.DeliveryProof Property — The delivery evidence of a delivery result.
• GemSpoolInfo.DequeuePending Property — true when success was accepted but removing the entry failed; call GemEquipment.RetrySpoolDequeue.
• GemSpoolInfo.Durability Property — How durably the change applied through this result was stored.
• GemSpoolInfo.EntryId Property — The ID of the delivered entry for a delivery result; otherwise 0.
• GemSpoolInfo.ErrorCount Property — The number of stream errors in an S2F44 received by the host.
• GemSpoolInfo.IsRequest Property — true for an S2F43, S2F59 or S6F23 request received by the equipment.
• GemSpoolInfo.PersistenceStatus Property — The PdcommStatus value of the last persistence failure on this result, which stays visible after GemEquipment.ConfirmSpoolReply; otherwise 0.
• GemSpoolInfo.ReplyReady Property — true when a prepared reply is retained and GemEquipment.RespondSpool sends it without applying the request again.
• GemSpoolInfo.RequestKind Property — GemRequestKind.SpoolConfigure, GemRequestKind.SpoolQuery, GemRequestKind.SpoolControl or GemRequestKind.SpoolDelivery.
• GemSpoolInfo.Responded Property — true when the reply to the request has been sent.
• GemSpoolInfo.SelectionCount Property — The number of stream selections in an S2F43 received by the equipment or in an S2F60 received by the host.
• GemSpoolInfo.SuccessAccepted Property — true when success was accepted for this delivery result.
• GemSpoolMessageKey.Function Property — The function of a primary message, an odd number.
• GemSpoolMessageKey.Stream Property — The stream, 2 to 127; stream 1 cannot be spooled.
• GemSpoolOptions.MaxBodyBytes Property — Gets the maximum encoded body size, in bytes, of one stored message.
• GemSpoolOptions.MaxCatalogEntries Property — Gets the maximum number of catalog entries, which also bounds the total number of functions in a received S2F43.
• GemSpoolOptions.MaxFunctionsPerStream Property — Gets the maximum number of functions in one stream selection.
• GemSpoolOptions.MaxMessages Property — Gets the maximum number of stored entries.
• GemSpoolOptions.MaxSerializedBytes Property — Gets the maximum size, in bytes, of the snapshot file of a file-backed spool; at least 144. An in-memory spool ignores it.
• GemSpoolOptions.MaxStreams Property — Gets the maximum number of stream selections in the local configuration or in a received S2F43.
• GemSpoolOptions.MaxTotalBodyBytes Property — Gets the maximum total encoded body size, in bytes, of all stored messages.
• GemSpoolPolicy.Enabled Property — Gets a value that indicates whether spooling may activate; it is independent of the stream selection.
• GemSpoolPolicy.MaxTransmit Property — Gets the maximum number of entries delivered in one transmission run, or 0 for no limit; the run ends when it is reached.
• GemSpoolPolicy.Overflow Property — Gets what happens to a new message when the spool is full.
• GemSpoolResultError.Acknowledgement Property — Gets the stream acknowledgement (STRACK), 1 to 4: 1 spooling is not allowed for the stream, 2 the stream is unknown, 3 a function is unknown for the stream, 4 a secondary function was specified.
• GemSpoolResultError.Functions Property — Gets the functions reported with the error as a SecsFormat.U1 array.
• GemSpoolResultError.Stream Property — Gets the rejected stream.
• GemSpoolResultSelection.Functions Property — Gets the selected functions as a SecsFormat.U1 array; an empty array selects every function of the stream.
• GemSpoolResultSelection.Stream Property — Gets the stream.
• GemSpoolSelection.Functions Property — The selected primary functions, without repetition; empty to select every function of the stream. Values that PDComm returns own a new array.
• GemSpoolSelection.Stream Property — The stream.
• GemSpoolState.Active Property — true while spooling is active. It ends when the spool is emptied by delivery or purge, or when spooling is disabled while the spool is empty.
• GemSpoolState.BodyBytes Property — The total encoded body size, in bytes, of the stored entries.
• GemSpoolState.CatalogCount Property — The number of catalog entries.
• GemSpoolState.Connected Property — true when the last synchronization saw the transport selected and GEM communicating.
• GemSpoolState.DeliveryPending Property — true while an entry is in flight or its successful delivery awaits removal.
• GemSpoolState.DequeuePending Property — true when a delivery succeeded but removing the entry failed; call GemEquipment.RetrySpoolDequeue.
• GemSpoolState.Discarded Property — The number of messages discarded because the spool was full, including old entries overwritten by GemSpoolOverflow.OverwriteOldest.
• GemSpoolState.Enabled Property — true when the local policy enables spooling.
• GemSpoolState.FullTime Property — The time the spool first became full during the current activation; valid when FullTimePresent is true.
• GemSpoolState.FullTimePresent Property — true when FullTime is set.
• GemSpoolState.MaxTransmit Property — The maximum number of entries per transmission run, or 0 for no limit.
• GemSpoolState.MessageCount Property — The number of stored entries.
• GemSpoolState.NextId Property — The entry ID that the next stored message receives.
• GemSpoolState.Overflow Property — The overflow policy.
• GemSpoolState.Persistent Property — true when the spool is backed by a snapshot file.
• GemSpoolState.Received Property — The number of selected messages offered to the spool, stored or discarded.
• GemSpoolState.SelectionCount Property — The number of stream selections.
• GemSpoolState.StartTime Property — The time spooling activated or stored its first entry; valid when StartTimePresent is true.
• GemSpoolState.StartTimePresent Property — true when StartTime is set.
• GemSpoolState.Stored Property — The number of messages stored.
• GemSpoolState.Synchronized Property — true when the last GemEquipment.SyncSpool still matches the current communication and selection state, so captures, replies and deliveries are allowed.
• GemSpoolState.Transmitted Property — The number of entries removed after a successful delivery.
• GemSpoolState.TransmittedInRun Property — The number of entries removed during the current transmission run.
• GemSpoolState.Transmitting Property — true while a transmission run accepted with S6F23 is in progress.
• GemSpoolWriteResult.AffectedCount Property — The number of entries overwritten by a capture, removed by a purge, or 1 for a dequeue; otherwise 0.
• GemSpoolWriteResult.Applied Property — true when a change was installed.
• GemSpoolWriteResult.Durability Property — How durably the change was stored.
• GemSpoolWriteResult.EntryId Property — The ID of the captured or removed entry; otherwise 0.
• GemSpoolWriteResult.Mutation Property — The change that was installed.
• GemSpoolWriteResult.PersistenceStatus Property — The PdcommStatus value of the persistence failure when Durability is GemSpoolDurability.Unconfirmed; otherwise 0.
• GemSpoolWriteResult.Selected Property — true when a change was installed; false when a captured message was not selected for spooling.
• GemSpoolWriteResult.Status Property — PdcommStatus.Ok, or PdcommStatus.SpoolUnconfirmed when the change was installed but its persistence could not be confirmed. Other statuses are thrown as PdcommException.
• GemState.Communication Property — The GEM communication state.
• GemState.Control Property — The equipment control state, or null for a host.
• GemState.EndpointId Property — The process-unique ID of the underlying HSMS endpoint.
• GemState.Generation Property — The connection generation of the underlying HSMS endpoint.
• GemState.OnlineMode Property — The equipment on-line mode, or null for a host.
• GemState.PendingCount Property — The number of GEM requests waiting for a reply (at most 32).
• GemState.PendingIds Property — The number of requested IDs held by the pending requests.
• GemState.Role Property — The role of the endpoint.
• GemState.VariableCount Property — The number of registered status variables; zero for a host.
• GemStatusName.Id Property — The status variable ID (SVID).
• GemStatusName.Name Property — The status variable name (SVNAME); a GemEquipment reports an empty name for an unknown ID.
• GemStatusName.Units Property — The units (UNITS); a GemEquipment reports empty units for an unknown ID.
• GemStatusValue.Id Property — Gets the requested status variable ID (SVID), or null when all values were requested, because an all-values reply carries no IDs.
• GemStatusValue.Value Property — Gets the status variable value. A GemEquipment answers an unknown ID with an empty list, but an empty list alone does not prove that the ID is unknown.
• GemStatusVariable.Id Property — The status variable ID (SVID).
• GemStatusVariable.Name Property — The status variable name (SVNAME); ASCII only.
• GemStatusVariable.Units Property — The units (UNITS); ASCII only, may be empty.
• GemStatusVariable.Value Property — The initial value. The worker encodes it while the start method runs, so the caller keeps ownership and may dispose it after the start method returns.
• GemWorker.Completion Property — Gets a task that completes when the worker thread exits.
• GemWorker.FormattedPrograms Property — Gets the asynchronous formatted process program operations of this worker.
• GemWorker.LocalAddress Property — Gets the numeric local socket address while the transport is listening or connected, or null otherwise.
• HsmsEventInfo.Aborted Property — Whether a received reply is an abort (function 0) instead of a normal reply.
• HsmsEventInfo.BodyLength Property — The size of the received message body, in bytes; zero when there is none.
• HsmsEventInfo.Code Property — The failure reason, protocol error or failed socket operation, depending on Kind.
• HsmsEventInfo.Detail Property — The frame error of an invalid frame, or the I/O error kind of a transport error.
• HsmsEventInfo.FromState Property — For HsmsEventKind.StateChanged, the previous connection state.
• HsmsEventInfo.Header Property — The message header, or null when the event has none.
• HsmsEventInfo.IsReply Property — Whether a received message is the reply to one of this endpoint's requests.
• HsmsEventInfo.Kind Property — The event kind.
• HsmsEventInfo.ToState Property — For HsmsEventKind.StateChanged, the new connection state.
• HsmsEventInfo.Token Property — The transaction the event belongs to: the request for a reply or failure, or the received primary's system bytes. Zero for state changes.
• HsmsEventInfo.Value1 Property — The first kind-specific value, for example a required size or a rejected message type.
• HsmsEventInfo.Value2 Property — The second kind-specific value, for example a limit or a reject reason.
• HsmsHeader.Function Property — The SECS-II function number.
• HsmsHeader.PType Property — The presentation type; 0 for SECS-II.
• HsmsHeader.ReplyExpected Property — Whether the W bit is set, meaning the sender expects a reply.
• HsmsHeader.SType Property — The session type; 0 for a data message.
• HsmsHeader.SessionId Property — The session ID (device ID).
• HsmsHeader.Stream Property — The SECS-II stream number, without the W bit.
• HsmsOptions.ConnectTimeoutMilliseconds Property — Gets the TCP connect timeout of an active endpoint, in milliseconds. HsmsEndpoint.Poll can block for up to this long during a connection attempt.
• HsmsOptions.InitialSystemBytes Property — Gets the first system bytes value this endpoint uses for its own requests.
• HsmsOptions.ItemLimits Property — Gets the limits applied to SECS-II message bodies.
• HsmsOptions.MaxApplicationBytes Property — Gets the largest total body size, in bytes, of events waiting for HsmsEndpoint.NextEvent.
• HsmsOptions.MaxApplicationEvents Property — Gets the capacity of the queue of events waiting for HsmsEndpoint.NextEvent.
• HsmsOptions.MaxEvents Property — Gets the capacity of the session's internal event queue; at least 72.
• HsmsOptions.MaxFrameBytes Property — Gets the largest frame, in bytes, that the endpoint sends or accepts, including the 14 framing bytes.
• HsmsOptions.MaxIoChunk Property — Gets the largest number of bytes read or written by one socket call.
• HsmsOptions.MaxQueuedBytes Property — Gets the largest total body size, in bytes, held in the session's internal event queue.
• HsmsOptions.MaxWriteBytes Property — Gets the largest total size, in bytes, of frames waiting to be written.
• HsmsOptions.MaxWriteFrames Property — Gets the largest number of frames waiting to be written.
• HsmsOptions.Mode Property — Gets whether the endpoint connects (HsmsMode.Active) or listens (HsmsMode.Passive).
• HsmsOptions.PollBudget Property — Gets the largest number of internal actions one HsmsEndpoint.Poll performs.
• HsmsOptions.SessionId Property — Gets the HSMS session ID (device ID) carried in data message headers.
• HsmsOptions.ShutdownTimeoutMilliseconds Property — Gets how long a stop may take to close the connection gracefully, in milliseconds.
• HsmsOptions.T3Milliseconds Property — Gets the T3 reply timeout, in milliseconds: how long a request waits for its reply.
• HsmsOptions.T5Milliseconds Property — Gets the T5 connect separation timeout, in milliseconds: the wait before an active endpoint reconnects.
• HsmsOptions.T6Milliseconds Property — Gets the T6 control transaction timeout, in milliseconds: how long Select, Deselect or Linktest waits.
• HsmsOptions.T7Milliseconds Property — Gets the T7 not-selected timeout, in milliseconds: how long a connection may stay not selected.
• HsmsOptions.T8Milliseconds Property — Gets the T8 network intercharacter timeout, in milliseconds, between bytes of one frame.
• HsmsOptions.WriteTimeoutMilliseconds Property — Gets how long a frame write may stall before the connection is treated as failed, in milliseconds.
• HsmsState.Closed Property — Whether the endpoint has fully closed after a stop. Closed does not mean that every event has been read.
• HsmsState.EndpointId Property — The process-local identity of the endpoint.
• HsmsState.Generation Property — The current connection generation.
• HsmsState.State Property — The connection state.
• HsmsToken.EndpointId Property — The process-local identity of the endpoint.
• HsmsToken.Generation Property — The connection generation in which the transaction was started.
• HsmsToken.SystemBytes Property — The system bytes (transaction ID) in the message header.
• HsmsWorker.Completion Property — Gets a task that completes when the worker thread has exited and released the endpoint.
• HsmsWorker.LocalAddress Property — Gets the endpoint's local socket address while it is listening or connected, or null otherwise.
• HsmsWorkerOptions.CommandCapacity Property — Gets the largest number of commands waiting to run on the worker thread; also the most commands run per loop.
• HsmsWorkerOptions.EventCapacity Property — Gets the largest number of events buffered for ReadEventsAsync; also the most native events read per loop.
• HsmsWorkerOptions.MaxCommandBytes Property — Gets the largest total size, in bytes, of the inputs (message bodies and captured values) of waiting commands.
• HsmsWorkerOptions.MaxEventBytes Property — Gets the largest total size, in bytes, of the events buffered for ReadEventsAsync.
• HsmsWorkerOptions.PollIntervalMilliseconds Property — Gets the longest time, in milliseconds, the worker sleeps between polls; it wakes earlier when work arrives.
• HsmsWorkerOptions.ShutdownTimeoutMilliseconds Property — Gets how long, in milliseconds, the worker may take to close the connection and drain after a stop or disposal before it fails with TimeoutException.
• Secs1Event.DiscardedPartial Property — For a fault, whether a partially received message was discarded.
• Secs1Event.FaultDetail Property — For an I/O fault, the Secs1IoStatus value of the failure; zero otherwise.
• Secs1Event.FaultKind Property — For a fault, its kind: 1 I/O error, 3 stream closed, 4 line protocol error, 5 invalid block, 6 reassembly error (2, an unknown control character, is no longer produced). Zero otherwise.
• Secs1Event.Kind Property — The event kind.
• Secs1Event.Message Property — For Secs1EventKind.Inbound, the received message with its body copied into managed memory. For other kinds, a placeholder with zero fields and an empty body.
• Secs1Event.Token Property — The submitted message that the event settles, for Secs1EventKind.OutboundComplete, Secs1EventKind.OutboundFailed, and a Secs1EventKind.Fault that aborted a send; zero otherwise.
• Secs1IoResult.Count Property — For Secs1IoStatus.Ok, the number of bytes read or written; it must not exceed the buffer length. Ignored for other statuses.
• Secs1IoResult.Status Property — The outcome of the operation.
• Secs1Message.Body Property — The message text, normally one encoded SECS-II item; split into blocks of up to 244 bytes on the wire. May be empty.
• Secs1Message.DeviceId Property — The device ID (0 to 32767).
• Secs1Message.Direction Property — The direction bit of the message.
• Secs1Message.Function Property — The SECS-II function number.
• Secs1Message.ReplyExpected Property — Whether the W bit is set, meaning the sender expects a reply.
• Secs1Message.Stream Property — The SECS-II stream number (0 to 127).
• Secs1Message.SystemBytes Property — The system bytes (transaction ID); the application chooses them for its own messages.
• Secs1Options.AckWaitTicks Property — The T2 protocol timeout for a reply to this endpoint: the ACK or NAK after a sent block and the length character after a sent EOT, in ticks.
• Secs1Options.GrantWaitTicks Property — The T2 protocol timeout for the EOT that answers this endpoint's ENQ, in ticks.
• Secs1Options.InboundProgressTicks Property — The T1 inter-character timeout while a block is being received, in ticks.
• Secs1Options.InterBlockTicks Property — The T4 inter-block timeout between the blocks of a multi-block message being received, in ticks.
• Secs1Options.MaxBlocks Property — The largest number of blocks in one message that the endpoint sends or reassembles.
• Secs1Options.MaxBodyBytes Property — The largest message body, in bytes, that the endpoint sends or reassembles.
• Secs1Options.MaxEventBodyBytes Property — The largest total body size, in bytes, of the queued events.
• Secs1Options.MaxEvents Property — The largest number of events the endpoint queues before it applies backpressure.
• Secs1Options.MaxIoChunk Property — The largest number of bytes passed to one read or write callback.
• Secs1Options.MaxOutboundBlocks Property — The largest number of blocks accepted for one submitted message.
• Secs1Options.MaxOutboundBodyBytes Property — The largest body, in bytes, accepted for one submitted message.
• Secs1Options.PollBudget Property — The largest number of I/O attempts one native poll makes.
• Secs1Options.Priority Property — The line contention priority: 0 (Secs1Priority.Master) keeps sending when both sides bid for the line, 1 (Secs1Priority.Slave) yields. Other values are rejected.
• Secs1Options.RetryLimit Property — The retry limit (RTY): how many times the endpoint restarts the ENQ handshake for a block that was not acknowledged before it reports the send as failed.
• Secs1State.EndpointId Property — The process-local identity of the endpoint.
• Secs1State.Faulted Property — Whether the line has faulted; the endpoint stops polling until Secs1Worker.ResetAsync clears the fault.
• Secs1State.Generation Property — The endpoint generation; every restart after a stop starts a new generation.
• Secs1State.Poisoned Property — Whether an internal failure poisoned the endpoint; it then only accepts destruction.
• Secs1State.Started Property — Whether the endpoint has been started and not stopped since.
• Secs1State.Stopped Property — Whether the endpoint has been stopped; a stop discards the runtime state.
• Secs1Token.EndpointId Property — The process-local identity of the endpoint that accepted the message.
• Secs1Token.Generation Property — The endpoint generation; every restart after a stop starts a new generation.
• Secs1Token.Value Property — The sequence number of the message within the generation; zero when no message is involved.
• Secs1Worker.CallbackException Property — Gets the most recent exception thrown by a read or write callback, or null if none was thrown.
• Secs1Worker.Completion Property — Gets a task that completes when the worker thread has exited, or faults with the error that ended it.
• Secs1WorkerOptions.CommandCapacity Property — The largest number of commands waiting to run; must be positive.
• Secs1WorkerOptions.EventCapacity Property — The largest number of events buffered for reading; must be positive.
• Secs1WorkerOptions.MaxCommandBytes Property — The largest total body size, in bytes, of waiting submissions; must not be negative.
• Secs1WorkerOptions.MaxEventBytes Property — The largest total body size, in bytes, of buffered events; must be at least Secs1Options.MaxBodyBytes.
• Secs1WorkerOptions.PollIntervalMilliseconds Property — How long, in milliseconds, the worker sleeps after each loop; each loop runs at most one queued command. Must be positive.
• Secs1WorkerOptions.ShutdownTimeoutMilliseconds Property — How long, in milliseconds, Secs1Worker.DisposeAsync waits for the worker thread; must be positive.
• SecsInfo.Count Property — Gets the number of children of a list, or the number of values in a primitive (payload bytes divided by the format's element width).
• SecsInfo.Depth Property — Gets the nesting depth of the tree; a primitive or an empty list has depth 1.
• SecsInfo.EncodedLength Property — Gets the size of the complete encoded item, in bytes.
• SecsInfo.Format Property — Gets the item's format.
• SecsInfo.NodeCount Property — Gets the number of items in the tree, including this item.
• SecsLimits.ItemBytes Property — Gets the largest payload of one primitive item, in bytes.
• SecsLimits.ItemCount Property — Gets the largest number of items in the tree, counting every list and primitive.
• SecsLimits.MessageBytes Property — Gets the largest complete encoded item, in bytes, including every header.
• SecsLimits.NestingDepth Property — Gets the largest nesting depth; a single item has depth 1.
• Gem300Axis Enum — The GEM300 object area that a capability belongs to.
• Gem300Capability Class — One capability of a GEM300 capability profile.
• Gem300CapabilityCatalog Class — A local, revisioned catalog of GEM300 capability profiles.
• Gem300CapabilityCatalogInfo Class — Describes the contents of a GEM300 capability catalog or of a snapshot of it.
• Gem300CapabilityInfo Class — Describes one capability of a GEM300 capability profile.
• Gem300CapabilityOptions Class — Limits that bound the contents of a Gem300CapabilityCatalog.
• Gem300CapabilityProfile Class — A named set of GEM300 capabilities, at most one per axis.
• Gem300CapabilityProfileInfo Class — Describes one profile of a GEM300 capability snapshot.
• Gem300CapabilitySnapshot Class — An immutable copy of a Gem300CapabilityCatalog at one revision.
• Gem300CatalogChange Class — The outcome of a change to a Gem300CapabilityCatalog.
• Gem300Status Enum — The status label that the application declares for one of its GEM300 capabilities.
• Gem300Verification Enum — The verification label stored for a GEM300 capability.
• GemAlarmChange Struct — Represents the result of GemEquipment.ObserveAlarm.
• GemAlarmConfiguration Class — Represents the alarm store that GemEquipmentWorker installs on its equipment endpoint at startup.
• GemAlarmDefinition Struct — Defines one equipment alarm for GemEquipment.ConfigureAlarms.
• GemAlarmEntry Struct — Represents one configured equipment alarm together with its text.
• GemAlarmInfo Struct — Represents the local state and metadata of one configured equipment alarm.
• GemAlarmOptions Class — Represents the capacity limits of the equipment alarm store installed by GemEquipment.ConfigureAlarms.
• GemAlarmResultInfo Struct — Describes an alarm report or alarm list carried by a host-side GemResult.
• GemAlarmState Struct — Represents a snapshot of the counters of the configured equipment alarm store.
• GemAlarmValue Struct — Represents one alarm entry received from the equipment together with its text.
• GemAlarmValueInfo Struct — Represents the fields of one alarm entry received from the equipment.
• GemBindingOptions Class — Represents the capacity limits of an equipment's report variable bindings.
• GemBindingState Struct — Represents the current state of an equipment's report variable bindings.
• GemCommandArgument Class — Represents one parameter name and value read from a received remote command request.
• GemCommandConfiguration Class — Represents the remote command store that GemEquipmentWorker installs on its equipment endpoint at startup.
• GemCommandDecision Enum — Specifies the application decision for a received remote command. The values mirror the host command acknowledge codes (HCACK).
• GemCommandDefinition Class — Defines one remote command that the equipment validates on receipt.
• GemCommandEntry Class — Represents one configured remote command and its name item.
• GemCommandError Class — Represents one parameter acknowledgement of a remote command result.
• GemCommandInfo Struct — Represents the metadata of one configured remote command.
• GemCommandIssue Class — Represents one parameter acknowledgement that the equipment returns in an S2F42 reply.
• GemCommandOptions Class — Represents the capacity limits of the equipment remote command store installed by GemEquipment.ConfigureCommands.
• GemCommandParameter Class — Represents one parameter that the host sends with a remote command.
• GemCommandParameterDefinition Class — Defines one parameter of a remote command definition.
• GemCommandParameterEntry Class — Represents one configured remote command parameter and its name item.
• GemCommandParameterInfo Struct — Represents the validation rules of one configured remote command parameter.
• GemCommandReply Struct — Represents the S2F42 reply that the equipment sent for a remote command.
• GemCommandResultInfo Struct — Describes a remote command request received by the equipment (S2F41) or a remote command reply received by the host (S2F42).
• GemCommandState Struct — Represents a snapshot of the counters of the configured remote command store.
• GemCommunicationState Enum — Represents the GEM communication state of an endpoint, driven by the S1F13/S1F14 Establish Communications transaction.
• GemConstantChange Class — Represents one new value for an equipment constant in an S2F15 (New Equipment Constant Send) request.
• GemConstantChangeEntry Class — Represents one ECID/ECV pair of a received S2F15 request and the value it would replace.
• GemConstantChangeInfo Struct — Represents the processing state of an S2F15 request result or an S2F16 reply result.
• GemConstantConfiguration Class — Represents the equipment constant store that GemEquipmentWorker installs on its equipment endpoint at startup.
• GemConstantDecision Enum — The application decision for a received S2F15 request; the value is the EAC (equipment acknowledge code) sent in S2F16.
• GemConstantDefinition Class — Represents one equipment constant to register with GemEquipment.ConfigureConstants.
• GemConstantEntry Class — Represents one registered equipment constant returned by GemEquipment.GetConstantAt.
• GemConstantField Enum — Selects one field of an equipment constant.
• GemConstantInfo Struct — Represents the declared shape of one registered equipment constant.
• GemConstantOptions Class — Configures the equipment constant store of a GemEquipment.
• GemConstantReply Struct — Represents the S2F16 reply sent by GemEquipment.RespondConstants.
• GemConstantState Struct — Represents the counters of the equipment constant store.
• GemConstantValue Class — Represents one entry of an S2F14 (Equipment Constant Data) reply.
• GemControlState Enum — Represents the GEM control state of an equipment endpoint.
• GemDataConfiguration Class — Represents the data variables and optional report bindings that a GemEquipmentWorker configures when it starts.
• GemDataDefinition Class — Represents the definition of one data variable in an equipment's data variable store.
• GemDataField Enum — Specifies which field of a data variable GemEquipment.GetData returns.
• GemDataInfo Struct — Represents the shape and cache state of one data variable.
• GemDataOptions Class — Represents the capacity limits of an equipment's data variable store.
• GemDataSample Class — Represents a data variable value supplied for one event report.
• GemDataSourceKind Enum — Specifies where a bound report variable gets its value.
• GemDataState Struct — Represents the current counters of an equipment's data variable store.
• GemDirectoryConfiguration Class — Represents the collection event directory that a GemEquipmentWorker configures when it starts.
• GemDirectoryEntryInfo Struct — Represents the ID and variable count of one directory entry.
• GemDirectoryField Enum — Specifies which field of a directory entry to read.
• GemDirectoryKind Enum — Specifies which namelist directory a host requests.
• GemDirectoryOptions Class — Represents the capacity limits of an equipment's collection event directory, which answers S1F23 (Collection Event Namelist Request).
• GemDirectoryState Struct — Represents the current counters of an equipment's event directory.
• GemEndpoint Class — Provides the members shared by GemHost and GemEquipment: a synchronous SEMI E30 (GEM) endpoint layered on one HSMS (SEMI E37) TCP connection.
• GemEnhancedCommandConfiguration Class — Represents the enhanced remote command store that GemEquipmentWorker installs on its equipment endpoint at startup.
• GemEnhancedCommandOptions Class — Represents the capacity limits of the equipment enhanced remote command store installed by GemEquipment.ConfigureEnhancedCommands.
• GemEnhancedCommandResultInfo Struct — Describes an enhanced remote command request received by the equipment (S2F49) or an enhanced remote command reply received by the host (S2F50).
• GemEnhancedCommandState Struct — Represents a snapshot of the counters of the configured enhanced remote command store.
• GemEnhancedObjectDefinition Class — Defines one object (OBJSPEC) and the enhanced remote commands it accepts.
• GemEnhancedObjectEntry Class — Represents one configured enhanced command object and its name item.
• GemEnhancedObjectInfo Struct — Represents the metadata of one configured enhanced command object.
• GemEquipment Class — A synchronous GEM (SEMI E30) equipment endpoint over one HSMS TCP connection.
• GemEquipmentOptions Class — Configures the GEM equipment layer of a GemEquipment.
• GemEquipmentSpoolConfiguration Class — Represents the spool that GemEquipmentWorker.StartWithSpoolingAsync attaches to the equipment.
• GemEquipmentWorker Class — A GEM equipment endpoint that runs on a dedicated polling thread and exposes asynchronous commands.
• GemError Enum — Describes why GEM rejected a message; reported in GemResultInfo.Code for GemResultKind.InvalidResponse and GemResultKind.Unhandled results.
• GemEvent Class — Represents one transport event delivered by GemWorker.ReadEventsAsync together with its GEM processing result.
• GemEventDefinition Struct — Represents a collection event stored by the equipment, with its enable state and linked reports.
• GemEventDirectoryDefinition Class — Represents one collection event entry of an equipment's event directory.
• GemEventInfo Struct — Represents the header fields of an event report (S6F11) that a host received.
• GemEventReport Struct — Represents one report inside a received event report (S6F11).
• GemFixedEventDefinition Class — One collection event of a fixed report catalog: its ID, its linked reports and its initial enable state.
• GemFormattedProgramActionResult Enum — The result an application reports for a start, step or cancel action with GemFormattedPrograms.SubmitActionResult.
• GemFormattedProgramCapabilityCommand Class — One command entry of the equipment's process capabilities catalog, sent in S7F22.
• GemFormattedProgramCapabilityCommandInfo Class — Describes one command of S7F22 process capabilities data.
• GemFormattedProgramCapabilityInfo Class — Describes an S7F21/S7F22 process capabilities transaction held by a GemResult.
• GemFormattedProgramCapabilityOptions Class — Limits for the S7F21/S7F22 process capabilities exchange and the equipment's capability catalog.
• GemFormattedProgramCommand Class — One command of a formatted process program: a command code and its parameters.
• GemFormattedProgramCommandInfo Class — Describes one command of a received, stored, selected or executed formatted process program.
• GemFormattedProgramConfiguration Class — The set of formatted process program services to enable on a GEM endpoint; a null option skips its service.
• GemFormattedProgramDependency Enum — Selects one dependency list of a command in an S7F22 process capabilities reply, for GemResult.GetFormattedProgramCapabilityDependencyAt.
• GemFormattedProgramDryRunInfo Class — Summarizes a formatted process program dry run report.
• GemFormattedProgramDryRunIssueInfo Class — Describes one issue of a formatted process program dry run report.
• GemFormattedProgramDryRunOptions Class — The policy version and limits of one formatted process program dry run.
• GemFormattedProgramDryRunOutcome Enum — The outcome of a formatted program dry run, in increasing order of severity.
• GemFormattedProgramDryRunReport Class — The result of a read-only structural check of the selected formatted process program.
• GemFormattedProgramExecutionAction Class — An action that a formatted process program execution asks the application to perform.
• GemFormattedProgramExecutionActionInfo Class — Describes an action that a formatted process program execution asks the application to perform.
• GemFormattedProgramExecutionActionToken Class — Identifies one action that a formatted process program execution asks the application to perform.
• GemFormattedProgramExecutionInfo Class — Summarizes the equipment's formatted process program execution at the time of a snapshot.
• GemFormattedProgramExecutionSnapshot Class — A read-only copy of the equipment's formatted process program execution state.
• GemFormattedProgramExecutionStart Class — The result of GemFormattedPrograms.StartExecution: the token of the new execution and its start action.
• GemFormattedProgramExecutionState Enum — The state of the equipment's formatted program execution tracker.
• GemFormattedProgramExecutionToken Class — Identifies one formatted process program execution of an equipment endpoint.
• GemFormattedProgramInfo Class — Describes an S7F27/S7F28 process program verification send held by a GemResult.
• GemFormattedProgramIssue Class — One issue of an S7F27 process program verification report.
• GemFormattedProgramOptions Class — Limits for S7F27/S7F28 process program verification sends.
• GemFormattedProgramPayload Class — A complete formatted process program: its identifier, model, software revision and commands.
• GemFormattedProgramQueryInfo Class — Describes an S7F25/S7F26 formatted process program request held by a GemResult.
• GemFormattedProgramQueryOptions Class — Limits for S7F25/S7F26 formatted process program requests and the equipment's program store.
• GemFormattedProgramSelectionInfo Class — Describes the equipment's formatted process program selection at the time of a snapshot.
• GemFormattedProgramSelectionSnapshot Class — A read-only copy of the equipment's formatted process program selection.
• GemFormattedProgramSelectionToken Class — Identifies the equipment's current formatted process program selection.
• GemFormattedProgramStoreAction Enum — Specifies how a formatted process program is written to the equipment's local store.
• GemFormattedProgramStoreEntryInfo Class — Describes one process program of a formatted process program store snapshot.
• GemFormattedProgramStoreInfo Class — Describes the equipment's formatted process program store.
• GemFormattedProgramStoreSnapshot Class — A read-only copy of the equipment's formatted process program store.
• GemFormattedProgramTerminalOutcome Enum — The final outcome an application reports with GemFormattedPrograms.CompleteExecution.
• GemFormattedProgramTransferInfo Class — Describes an S7F23/S7F24 formatted process program send held by a GemResult.
• GemFormattedProgramTransferOptions Class — Limits for S7F23/S7F24 formatted process program sends.
• GemFormattedProgramVerificationNegotiationInfo Class — Describes an S7F29/S7F30 process program verification negotiation held by a GemResult.
• GemFormattedProgramVerificationNegotiationOptions Class — Limits for the S7F29/S7F30 process program verification inquire and grant that precedes an S7F27 verification send.
• GemFormattedProgramVerificationRequestInfo Class — Describes an S7F31/S7F32 verification request held by a GemResult.
• GemFormattedProgramVerificationRequestOptions Class — Limits for S7F31/S7F32 verification requests.
• GemFormattedPrograms Class — Provides the formatted process program services of a GEM endpoint: the S7F21 to S7F32 transactions, the equipment's local formatted program store and capability catalog, program selection, dry runs and execution tracking.
• GemFormattedProgramsWorker Class — Runs formatted process program operations on a GEM worker's polling thread.
• GemHost Class — A synchronous GEM (SEMI E30) host endpoint over one HSMS TCP connection.
• GemHostOptions Class — Configures the GEM host layer of a GemHost.
• GemHostWorker Class — A GEM host endpoint that runs on a dedicated polling thread and exposes asynchronous commands.
• GemLinkSpec Struct — Represents one event link that a host sends in S2F35 (Link Event Report).
• GemOnlineMode Enum — Selects whether equipment enters GemControlState.OnlineLocal or GemControlState.OnlineRemote when it goes on-line.
• GemOutcome Enum — Describes what GEM processing concluded for a GemResult.
• GemOwnedSnapshot Class — The base class of formatted process program snapshots, reports and actions that own native memory.
• GemProgramConfiguration Class — Represents the process program store that a worker installs at startup.
• GemProgramDefinition Class — Represents a process program that a worker stores at startup.
• GemProgramDurability Enum — Describes how durably a local process program change was installed.
• GemProgramEntry Class — Represents a copy of one stored process program.
• GemProgramField Enum — Selects a field of a process program result for GemResult.GetProgramItem.
• GemProgramGrantPolicy Enum — Selects whether a received S7F3 (Process Program Send) needs an earlier S7F1/S7F2 grant.
• GemProgramInfo Struct — Represents the state of a received stream 7 process program request or reply.
• GemProgramOptions Class — Configures the process program store and the stream 7 transactions of a GEM endpoint.
• GemProgramPutMode Enum — Selects how a process program is stored when its PPID may already exist.
• GemProgramState Struct — Represents the counters of a process program store.
• GemProgramWriteInfo Struct — Represents the outcome of a local process program change.
• GemQueryInfo Struct — Represents the report query details of a GemResult.
• GemQueryReportInfo Struct — Represents one report of an S6F16 event report reply.
• GemQueryValue Class — Represents one value of a report query reply.
• GemReportBinding Class — Represents a binding from a report variable ID (VID) to the source of its value.
• GemReportBindingEntry Class — Represents a report variable binding read back from the equipment.
• GemReportConfiguration Class — Represents the event report store that a GemEquipmentWorker configures when it starts.
• GemReportDefinition Struct — Represents a report definition: a report ID and its ordered variable IDs.
• GemReportOptions Class — Represents the capacity limits of an equipment's event report store: collection events, reports and the links between them.
• GemReportQueryKind Enum — Identifies the S6 report query transaction; the values equal the matching GemRequestKind members.
• GemReportSpec Struct — Represents one report definition that a host sends in S2F33 (Define Report).
• GemReportState Struct — Represents the current counters of an equipment's event report store.
• GemRequestKind Enum — Identifies the GEM transaction that a GemResult belongs to.
• GemResult Class — Represents the outcome of processing one transport event with the GEM layer.
• GemResultInfo Struct — Represents the summary of a GemResult.
• GemResultKind Enum — Classifies how GemEndpoint.HandleEvent processed a transport event.
• GemRole Enum — Identifies which side of a SEMI E30 (GEM) conversation an endpoint plays.
• GemSpoolCommand Enum — Specifies the request spooled data code (RSDC) of an S6F23 (Request Spooled Data) message.
• GemSpoolDeliveryProof Enum — Specifies the evidence that a delivery result carries for a delivered spool entry.
• GemSpoolDurability Enum — Specifies how durably a spool change was stored.
• GemSpoolEntry Class — Represents a copy of one stored spool entry.
• GemSpoolEntryInfo Struct — Represents the header of one stored spool entry.
• GemSpoolHostOptions Class — Represents the limits of the spooling requests that a host sends and of the replies it accepts.
• GemSpoolInfo Struct — Represents the spooling details of a GemResult.
• GemSpoolMessageKey Struct — Represents a primary message (stream and function) in the equipment spool catalog.
• GemSpoolMutation Enum — Specifies which change a spool operation installed.
• GemSpoolOptions Class — Represents the limits of an equipment spool.
• GemSpoolOverflow Enum — Specifies what the equipment spool does with a new message when it is full.
• GemSpoolPolicy Class — Represents the local spooling policy of the equipment.
• GemSpoolResultError Class — Represents one stream error of an S2F44 reply that rejected an S2F43 request.
• GemSpoolResultSelection Class — Represents one stream selection read from a spooling result.
• GemSpoolSelection Struct — Represents the functions of one stream that are selected for spooling.
• GemSpoolState Struct — Represents the counters, policy and flags of the equipment spool.
• GemSpoolWriteResult Struct — Represents the outcome of an equipment spool operation that can change the spool.
• GemState Struct — Represents a snapshot of the GEM state of an endpoint.
• GemStatusName Struct — Represents the name and units of a status variable.
• GemStatusValue Class — Represents one status variable value from an S1F4 reply.
• GemStatusVariable Struct — Represents a status variable that GemEquipmentWorker registers on its endpoint at startup.
• GemWorker Class — Provides the members shared by GemHostWorker and GemEquipmentWorker: a GEM endpoint owned by a dedicated polling thread.
• HsmsConnectionState Enum — The connection state of an HSMS endpoint.
• HsmsEndpoint Class — A synchronous HSMS (SEMI E37) endpoint that exchanges SECS-II messages over TCP/IP.
• HsmsEvent Class — One event taken from an HSMS endpoint: a state change, a received message, a failure or an error.
• HsmsEventInfo Struct — Describes one HsmsEvent.
• HsmsEventKind Enum — The kind of an HsmsEvent.
• HsmsFailureReason Enum — Why a request or control transaction failed, reported in HsmsEventInfo.Code of a HsmsEventKind.Failed event.
• HsmsFrameError Enum — The frame-level error reported in HsmsEventInfo.Detail when the protocol error is HsmsProtocolError.InvalidFrame.
• HsmsHeader Struct — The 10-byte HSMS message header of a received message.
• HsmsIoErrorKind Enum — The portable kind of a socket error, reported in HsmsEventInfo.Detail of a HsmsEventKind.TransportError event.
• HsmsIoOperation Enum — The socket operation that failed, reported in HsmsEventInfo.Code of a HsmsEventKind.TransportError event.
• HsmsMode Enum — The HSMS (SEMI E37) connection mode of an endpoint.
• HsmsOptions Class — Options for an HSMS (SEMI E37) endpoint: role, session, timers and resource limits.
• HsmsProtocolError Enum — The HSMS protocol violation reported in HsmsEventInfo.Code of a HsmsEventKind.ProtocolError event.
• HsmsState Struct — A snapshot of an HSMS endpoint's state.
• HsmsToken Struct — Identifies one transaction of an HSMS endpoint.
• HsmsWorker Class — Runs an HsmsEndpoint on a dedicated background thread and exposes it through asynchronous methods.
• HsmsWorkerOptions Class — Queue capacities and timing for HsmsWorker, GemEquipmentWorker and GemHostWorker.
• Secs1Direction Enum — The message direction that a SECS-I block header carries in its R-bit.
• Secs1Event Class — An event produced by a Secs1Worker.
• Secs1EventKind Enum — The kind of a Secs1Event.
• Secs1IoResult Struct — The result of a Secs1Read or Secs1Write callback.
• Secs1IoStatus Enum — The result status that a Secs1Read or Secs1Write callback reports to the endpoint.
• Secs1Message Class — A SECS-I message: block header identity plus the message body.
• Secs1Options Class — Line timing, retry and capacity options for a SECS-I (SEMI E4) endpoint.
• Secs1Priority Enum — The line contention priority of a SECS-I (SEMI E4) endpoint, used in Secs1Options.Priority.
• Secs1Read Delegate — Reads bytes from the serial line for a Secs1Worker.
• Secs1State Class — A snapshot of a SECS-I endpoint's lifecycle flags.
• Secs1Token Class — Identifies one message submitted to a SECS-I endpoint.
• Secs1Worker Class — Runs a SECS-I (SEMI E4) serial line protocol endpoint on a dedicated background thread.
• Secs1WorkerOptions Class — Queue capacities and timing for a Secs1Worker.
• Secs1Write Delegate — Writes bytes to the serial line for a Secs1Worker.
• SecsFormat Enum — SECS-II item format codes (SEMI E5), as carried in the format byte of an encoded item.
• SecsInfo Struct — Describes the shape of a SECS-II item.
• SecsItem Class — An immutable SECS-II (SEMI E5) data item held in native memory: a list or a typed primitive value array.
• SecsLimits Struct — Resource limits that bound how SECS-II items are created, decoded and encoded.